ABB Zenith ZTG 30 Скачать руководство пользователя страница 81

Страница: 81 / 116

5.6.6.2 Access from the display /
Ekip Com EtherNet/IP

With modules connected and energized,
the presence of the modules on the mod-
ule slot activates additional menus on
the display:

• To set the addressing of the modules.
• In order to display information on the

modules.

The following table illustrates the path
from the display, for setting the function
and addressing of the modules:

Settings (*Default value)

Description

:
Modules (Optional modules)

Ekip Com EtherNet/IP

Force Static IP address

Off*

Dynamic IP address.

Static IP address.

Static IP Address

Displayed with static IP Address enabled, it
must be selected in order to insert the IP
Address of the modules.

Static Network Mask

Displayed with static IP Address enabled, it
must be selected in order to insert the subnet
mask of the modules.

Static Gateway addr

Displayed with static IP Address enabled, it
must be selected in the presence of multiple
subnets, in order to insert the IP Address of
the node to which the modules are connected.

—
Table 5.24 The path for setting the function and addressing of the modules
of the Ekip Com Ethernet/IP -module from the display

CD
, T

Содержание Zenith ZTG 30





















































































































Результаты поиска

Содержание Zenith ZTG 30

Отзывы:

Похожие инструкции для Zenith ZTG 30

Бренды по названию

Популярные бренды

ABB Zenith ZTG 30, Руководство по эксплуатации, техническому обслуживанию и установке

Результаты поиска

Содержание Zenith ZTG 30

Отзывы:

Похожие инструкции для Zenith ZTG 30

Бренды по названию

Популярные бренды