ABB Zenith ZTG 30 Скачать руководство пользователя страница 67

Страница: 67 / 116

5.6.2.3 Access from the display
/ Ekip Com Profibus DB -module

With modules connected and energized,
the presence of the modules on the mod-
ule slot activates additional menus on
the display.

The following table illustrates the path for
accessing the configuration parameters
of the modules from the display:

Settings (*Default value)

Description

:
Modules (Optional modules)

Ekip Com Profibus DB

Serial address

1…125, default 125*

Address to be assigned to the modules.
IMPORTANT: devices connected to the same
network must have different addresses

—
Table 5.10 Configuration of Ekip Com Profibus DB -module in HMI

The following table illustrates the path
from the display for accessing informa-
tion on the module:

About

Description

:
Modules (Optional modules)

Ekip Com Profibus DB -module

Serial number

Version

Software version

—
Table 5.11 Information of Ekip Com Profibus DB -module in HMI

CD
, T

Содержание Zenith ZTG 30





















































































































Результаты поиска

Содержание Zenith ZTG 30

Отзывы:

Похожие инструкции для Zenith ZTG 30

Бренды по названию

Популярные бренды

ABB Zenith ZTG 30, Руководство по эксплуатации, техническому обслуживанию и установке

Результаты поиска

Содержание Zenith ZTG 30

Отзывы:

Похожие инструкции для Zenith ZTG 30

Бренды по названию

Популярные бренды