ABB Zenith ZTG 30 Скачать руководство пользователя страница 49 | Manualshive

Страница: 49 / 116

background image

49

1

Settings

*Default

Standard I/O Settings (continued)

O 01 (continued)

Function (continued)

Pre-transfer Signal

Signal is activated and transfer is delayed according
to pre-transfer delay. Signal is kept activated
according to post-transfer delay after transfer.

Source 1 Available

No anomalies in S1 voltage supply.

Source 2 Available

No anomalies in S2 voltage supply.

Load Shed 1

Used for shedding non-essential loads before
transferring to non-priority source. Signal is
activated before transferring to non-priority source
according to load shed delay and kept activated until
load is transferred back to priority source.

Elevator pre-signal

Signal is activated and transfer is delayed according
to Elevator pre-signal delay. Signal is kept activated
according to Elevator post-signal delay after
transfer.

Contact
type

NC

Active open.

NO*

Active closed.

Modules (See Chapter 5, Electronic accessories)

System

RESET to Factory Setting

Restore default parameter values.

Date

1)

Month day, year

Time

1)

Hours:Minutes

Language

English*
Italian
French
German
Spanish
Russian
Chinese

New Password

Five digits

Temperature Unit

Celsius*
Fahrenheit

Clock Format

24 h*
12 h

Display Contrast

10 - 100% (30 %*)

1)

RTC capacitor must be charged before inserting Date/Time. RTC capacitor is charged from source voltage (not AUX)

and takes about 10 minutes. RTC capacitor keeps the date/time saved for 48 h in case of no source voltage available.

«
...
47
48
49
50
51
...
»

Содержание Zenith ZTG 30





















































































































Отзывы:

Нет отзывов

Похожие инструкции для Zenith ZTG 30

Бренд: eao Страницы: 2

Бренд: eao Страницы: 2

Бренд: Yamamoto Electric Works Co., Ltd. Страницы: 15

Бренд: J-Tech Digital Страницы: 28

Бренд: Generac Power Systems Страницы: 20

Бренд: V7 Страницы: 35

MCD-LED17 series

Бренд: Raritan Страницы: 89

Бренд: Avenview Страницы: 10

Бренд: Accton Technology Страницы: 7

Бренд: StarTech.com Страницы: 16

Бренд: Quartz Страницы: 43

AV Selector 310

Бренд: Hama Страницы: 21

Бренд: DX Engineering Страницы: 4

Бренд: Lindy Страницы: 54

Бренд: Opengear Страницы: 109

QSW-M2108 Series

Бренд: QNAP Страницы: 28

CrossPoint 42 HVA

Бренд: Extron electronics Страницы: 46

Бренд: Kramer Страницы: 85

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды