1SDH002031A1002 ECN000092998 Rev. B
SACE Tmax XT2
– XT4 | 159
Remote
configurations
From the service connector (via Ekip Connect) or with communication by system bus it is possible
to access additional parameters:
Parameter
Description
Default
Client/Server
Parameter for changing the configuration of the module from Server
Only to Client and Server and integrating it into an interactive data
exchange network (see
Ekip Com Hub
on page156)
IMPORTANT: if Client/Server, the module enables
the data to be exchanged as a normal Server
function
Server
only
Enable IEEE 1558
Permits the IEEE 1588 protocol for distributing the clock and
synchronization signal to be enabled
(1)
OFF
IEEE 1588 Master
Enables the module to be set as a master in the network segment
to which it belongs (synchronization clock)
OFF
IEEE 1588 Delay
mechanism
Enables the data exchange mode between module and master,
between Peer-to-Peer and End-to-End to be chosen
End-to-
End
Enable SNTP client
Permits enabling of SNTP distribution protocol of the clock and
synchronization signal
(1)
OFF
SNTP Server Address
Enables the network server to be set that supplies SNTP
0.0.0.0
Time zone
Defines the time zone to be used for synchronism
+00:00
Daylight Saving
Time
Enables it to be selected whether there is daylight saving
time(ON) or not (OFF) in the country to which the synchronization
time refers.
OFF
Disable Gratuitos
ARP
Permits (Enabled ARP) the periodic generation of a Gratuituos ARP
message to be enabled that is used by Ekip Connect to find rapidly
the modules with Ethernet scanning without its IP address being
known beforehand
ARP
enabled
Access protected by
password
Enables the writing operations conducted by the network to be
protected by a password (password request)
Standard
mode
TCP Modbus
password
With
access protected by enabled
password, this is the password
to use before each writing session
(2)
Local
access
NOTES:
(1)
Enable IEEE 1558 and Enable SNTP client
must not be enabled simultaneously
(2) the parameter can be modified only by system bus in remote configuration
Remote link
configurations
Further link function parameters are available:
Parameter
Description
Default
Actor link (1-15)
IP address of each actor (1 to15)
0.0.0.0
Remote programmable
status (A-D)
Configuration parameters of programmable statuses
actor selection (actor from 1 to 15) that activates
programmable status
event of the actor that determines the change of
programmable status
Actor 1
None
Word status (A-D)
Word configuration parameters:
actor selection (actor from 1 to 15) from which the
word status is taken
selection of the taken word
None
1 global
Diagnosis
Active (passive diagnosis) or deactivated diagnosis (no
diagnosis) of the diagnosis of cabled selectivity
No diagnosis
Timeout diagnosis control
Diagnosis checking interval, if active available between
30 s, 1 min, 10 min, 60 min
30 seconds
Zone selectivity type
Configuration of hardware selectivity (only HW) or
hardware and logic selectivity (mixed)
Only HW
Repeat Configuration Mask
interactive mask for selecting selectivity do be sent also
to the upper levels (even if not active on the programmed
device)
0x0000
Содержание SACE Tmax XT2
