ABB ret650 Скачать руководство пользователя страница 99

Страница: 99 / 110

GUID-31DF5495-91F1-4A4B-8FD5-50625038961E V1 EN

Figure 10:

Testing a trip contact

1 Trip contact under test
2 Current limiting resistor

•

To check the status of the output circuits driving the output relay via the
LHMI, select

Main menu/Tests/Binary output values/Binary output

modules

and then navigate to the board with the actual binary output to be

checked.

•

Test and change the relay state manually.
1.

To set the IED to test mode, select

Main menu/Tests/IED

testmode1:TESTMODE/TestMode

and set the parameter to

To operate or force the output relay to operate, select and then navigate
to the board with the actual binary output relay to be operated/forced.

Select the BOn_PO to be operated/forced and use

and

operate the actual output relay.
In PCM600, only the result of these operations can be checked by right-
clicking the product and selecting Signal Monitoring tool and then

1MRK 504 126-UEN -

Section 8

Troubleshooting

Commissioning Manual

Содержание ret650














































































































Результаты поиска

Содержание ret650

Отзывы:

ABB ret650, Руководство по вводу в эксплуатацию, Страница: 99 / 110

Результаты поиска

Содержание ret650

Отзывы: