ABB ret650 Скачать руководство пользователя страница 58

Страница: 58 / 110

Signal Monitoring in PCM600 shows the same signals that are available on the
local HMI.

The Breaker failure protection function CCRBRF should normally be tested in
conjunction with some other function that provides a start signal. An external
START signal can also be used.

To verify the settings in the most common back-up trip mode

1 out of 3

, it is

sufficient to test phase-to-earth faults.

At mode

2 out of 4

the phase current setting,

IP>

can be checked by single-phase

injection where the return current is connected to the summated current input. The
value of residual (earth fault) current IN set lower than

IP>

is easiest checked in back-

up trip mode

1 out of 4

6.4.6.1

Checking the phase current operate value,

IP>

Check the current level

IP>

where setting

FunctionMode

Current

and setting

BuTripMode

1 out of 3

2 out of 4

as set under

Main menu/Settings/IED

Settings/Current/CCRBRF(50BF)/1:CCRBRF

Apply the fault condition, including START of CCRBRF, with a current
below set

IP>

Repeat the fault condition and increase the current in steps until a trip occurs.

Compare the result with the set

IP>

Disconnect AC and START input signals.

Note! If

NoI>check

Retrip off

is set, only back-up trip can

be used to check set

IP>

6.4.6.2

Checking the residual (earth fault) current operate value

IN> set

below

IP>

Check the low set

IN>

current where setting

FunctionMode

Current

and setting

BuTripMode

1 out of 4

as set under

Main menu/Settings/IED Settings/Current/

CCRBRF(50BF)/1:CCRBRF

Apply the fault condition, including START of CCRBRF, with a current just
below set

IN>Pickup_N

Repeat the fault condition and increase the current in steps until trip appears.

Compare the result with the set

IN>

Disconnect AC and START input signals.

Section 6

1MRK 504 126-UEN -

Testing functionality

Commissioning Manual

Содержание ret650














































































































Результаты поиска

Содержание ret650

Отзывы:

ABB ret650, Руководство по вводу в эксплуатацию, Страница: 58 / 110

Результаты поиска

Содержание ret650

Отзывы: