ABB ret650 Скачать руководство пользователя страница 78 | Manualshive

Страница: 78 / 110

ABB ret650 Скачать руководство пользователя страница 78

General/UVPartBk

and

Main menu/Settings/IED Settings/Control/

TR8ATCC (90)/n:TR8ATCC/General/OVPartBk

.

3.

Decrease the injected voltage slightly below the

Umin

value and check for the

corresponding blocking or alarm condition on the local HMI. For an alarm
condition, the voltage regulation function is not blocked and a raise command
should be issued from the IED.

4.

Increase the applied voltage slightly above the

Umax

value and check for the

corresponding blocking or alarm condition on the local HMI. For an alarm
condition, the voltage regulation function is not blocked and a lower
command should be issued from the IED.

6.7.1.6

Check the overcurrent block function

1.

Confirm the setting for

Iblock

in the local HMI under

Main menu/Settings/

IED Settings/Control/TR8ATCC (90)/n:TR8ATCC/TCCtrl/Iblock

2.

Confirm the voltage control function response to an applied current above

Iblock

, by reviewing the settings in the local HMI under

Main menu/Settings/

IED Settings/Control/TR8ATCC (90)/n:TR8ATCC/General/OCBk

.

3.

Inject a current higher than the

Iblock

setting and confirm the alarm or

blocking condition is present on the local HMI. If an automatic or total
blocking condition occurs, change the applied secondary voltage and confirm
that no tap change commands are issued from the associated binary outputs.
This situation can also be confirmed through reviewing the disturbance and
service reports on the local HMI.

6.7.1.7

Automatic voltage control for tap changer, parallel control TR8ATCC

Master follower voltage regulation

1.

For the transformers connected in the parallel group, confirm that

OperationPAR

is set to

MF

.

2.

For parallel operation, it is also recommended to confirm for parallel group
membership, defined by setting

TnRXOP

in the local HMI under

Main menu/

Settings/IED Settings/Control/TR8ATCC (90)/n:TR8ATCC/ParCtrl

The general parallel arrangement of transformers are defined by setting

TnRXOP

to

On

or

Off

. The following rules are applicable on the settings

T1RXOP

–

T4RXOP

.

If IED

T1

and

T2

are connected,

•

T1RXOP

shall be set to

On

in instance 2 of TR8ATCC,

•

T2RXOP

shall be set to

On

in instance 3 of TR8ATCC,

•

T2RXOP

and

T3RXOP

shall be set to

On

in instance 1 of TR8ATCC,

and so on.

Section 6

1MRK 504 126-UEN -

Testing functionality

70

Commissioning Manual

«
...
76
77
78
79
80
...
»

Содержание ret650















































































































Отзывы:

Нет отзывов