ABB ret650 Скачать руководство пользователя страница 70

Страница: 70 / 110

Values of the logical signals for SAPTUF are available on the local HMI under

Main menu/Tests/Function status/Frequency/SAPTUF(81,f<)/X:SAPTUF

. The

Signal Monitoring in PCM600 shows the same signals that are available on the
local HMI.

6.6.1.1

Verifying the settings

Verification of START value and time delay to operate

Check that the IED settings are appropriate, especially the START value and
the definite time delay.

Supply the IED with three-phase voltages at their rated values.

Slowly decrease the frequency of the applied voltage, until the START signal
appears.

Note the operate value and compare it with the set value.

Increase the frequency until rated operating levels are reached.

Check that the START signal resets.

Instantaneously decrease the frequency of the applied voltage to a value about
20% lower than the operate value.

Measure the time delay of the TRIP signal, and compare it with the set value.

Extended testing

The test above can be repeated to check the time to reset.

The tests above can be repeated to test the frequency dependent inverse time
characteristic.

Verification of the low voltage magnitude blocking

Check that the IED settings are appropriate, especially the

StartFrequency

and the

tDelay

and the

MinValFreqMeas

in the SMAI preprocessing function.

Supply the IED with three-phase voltages at rated values.

Slowly decrease the magnitude of the applied voltage, until the BLKDMAGN
signal appears.

Note the voltage magnitude value and compare it with the SMAI set value

MinValFreqMeas

Slowly decrease the frequency of the applied voltage, to a value below

StartFrequency

Check that the START signal does not appear.

Wait for a time corresponding to

tDelay

, and check that the TRIP signal does

not appear.

6.6.1.2

Completing the test

Continue to test another function or end the testing by setting the parameter

TestMode

Off

under

Main menu/Tests/IED test mode/1:TESTMODE

. If

another function is tested, then set the parameter

Blocked

under

Main menu/

Section 6

1MRK 504 126-UEN -

Testing functionality

Commissioning Manual

Содержание ret650














































































































Результаты поиска

Содержание ret650

Отзывы:

ABB ret650, Руководство по вводу в эксплуатацию, Страница: 70 / 110

Результаты поиска

Содержание ret650

Отзывы: