ABB ret650 Скачать руководство пользователя страница 49 | Manualshive

Страница: 49 / 110

ABB ret650 Скачать руководство пользователя страница 49

12. If available on the test set a second harmonic current of about 20% (assumes

15% setting on I1/I2ratio parameter) can be added to the fundamental tone in
phase L1. Increase the current in phase L1 above the start value measured in
step

. Repeat test with current injection in phases L2 and L3 respectively.

Note that during this test setting

SOTFMode

must be set to

Off

.

The balancing of currents flowing into and out of the differential zone is
typically checked by primary testing when suitable supply facilities exist on
site.
Fifth harmonic blocking can be tested in a similar way. Note, the blocking
level for the fifth harmonic is 10% higher than the I5/I1Ratio setting.

6.3.1.2

Completing the test

Continue to test another function or end the testing by setting the parameter

TestMode

to

Off

under

Main menu/Tests/IED test mode/1:TESTMODE

. If

another function is tested, then set the parameter

Blocked

to

No

under

Main menu/

Tests/Function test modes/Differential/T2WPDIF(87T,Id)/1:T2WPDIF

for the

function, or for each individual function in a chain, to be tested next. Remember to
set the parameter

Blocked

to

Yes

, for each individual function that has been tested.

Continue to test another function or end the testing by setting the parameter

TestMode

to

Off

under

Main menu/Tests/IED test mode/1:TESTMODE

. If

another function is tested, then set the parameter

Blocked

to

No

under

Main menu/

Tests/Function test modes/Differential/T3WPDIF(87T,Id)/1:T3WPDIF

for the

function, or for each individual function in a chain, to be tested next. Remember to
set the parameter

Blocked

to

Yes

, for each individual function that has been tested.

6.3.2

Restricted earth fault protection, low impedance REFPDIF

Prepare the IED for verification of settings as outlined in

5.1 "Preparing the IED to

verify settings"

.

Values of the logical signals for REFPDIF are available on the local HMI under

Main menu/Tests/Function status/Differential/REFPDIF(87,INd)/
X:REFPDIF

. The Signal Monitoring in PCM600 shows the same signals that are

available on the local HMI.

6.3.2.1

Verifying the settings

1MRK 504 126-UEN -

Section 6

Testing functionality

41

Commissioning Manual

«
...
47
48
49
50
51
...
»

Содержание ret650















































































































Отзывы:

Нет отзывов