manualshive.com logo in svg

ABB REL-300, Инструкция

Поделиться
Скачать
ABB REL-300 Скачать руководство пользователя страница 22

I.L. 40-385.1B

viii

(5/92)

FIGURES

FIGURE NO.

PAGE

1-1.

MDAR Relay Assembly showing FT-14 Switch Covers ............................................................ 1-6

1-2

Layout of MDAR Modules within Inner and Outer Chassis ....................................................... 1-7

1-3

INCOM/PONI Communication Interface Device (photo) ........................................................... 1-8

1-4

Simplified Block Diagram of MDAR Relay................................................................................. 1-9

1-5

MDAR Relay Program Functions ............................................................................................ 1-10

2-1.

CO-2 Curve Characteristics ...................................................................................................... 2-4

2-2.

CO-5 Curve Characteristics ...................................................................................................... 2-5

2-3.

CO-6 Curve Characteristics ...................................................................................................... 2-6

2-4.

CO-7 Curve Characteristics ...................................................................................................... 2-7

2-5.

CO-8 Curve Characteristics ...................................................................................................... 2-8

2-6.

CO-9 Curve  Characteristics ..................................................................................................... 2-9

2-7.

CO-11Curve Characteristics ................................................................................................... 2-10

2-8.

MDAR Outline Drawing ........................................................................................................... 2-11

3-1.

MDAR Characteristics/R-X Diagram ....................................................................................... 3-17

3-2.

Mho Characteristic for Phase-to-Ground Faults ...................................................................... 3-17

3-3.

Mho Characteristics for Three-Phase Faults (No Load Flow) ................................................. 3-18

3-4.

Mho Characteristics for Phase-to-Phase and Two-Phase-to-Ground

Faults (No Load Flow) ............................................................................................................. 3-18

3-5.

MDAR Zone-1 Trip Logic......................................................................................................... 3-19

3-6.

MDAR Zone-2 Trip Logic......................................................................................................... 3-19

3-7.

MDAR Zone-3 Trip Logic......................................................................................................... 3-20

3-8.

MDAR Zone-1 Extension Scheme .......................................................................................... 3-20

3-9.

Inverse Time Overcurrent Ground Backup Logic .................................................................... 3-21

3-10.

Loss of Potential Logic ............................................................................................................ 3-21

3-11.

Loss of Potential Logic (System Diagram) .............................................................................. 3-22

3-12.

AC Current Monitoring Logic ................................................................................................... 3-22

3-13.

Overcurrent Supervision.......................................................................................................... 3-23

3-14.

Instantaneous Overcurrent Highset Trip Logic ........................................................................ 3-23

3-15.

MDAR Close-Into-Fault Trip (CIFT) Logic ............................................................................... 3-24

3-16.

MDAR Unequal-Pole-Closing Load Pickup Trip Logic ............................................................ 3-24

3-17.

Load Loss Accelerated Trip Logic ........................................................................................... 3-25

3-18a.

Out-of-Step Block Logic .......................................................................................................... 3-25

3-18b.

Out-of-Step Block Logic (Blinder Characteristic) ..................................................................... 3-25

3-19.

Reclosing Initiation Logic......................................................................................................... 3-26

3-20.

Single Pole Trip Logic ............................................................................................................. 3-26

3-21.

POTT/Unblocking Pilot Relay .................................................................................................. 3-27

3-22.

POTT/Unblocking Pilot Trip Logic ........................................................................................... 3-27

3-23.

Carrier Keying/Receiving Logic in POTT/Unblocking schemes .............................................. 3-28

3-24.

PUTT Keying Logic ................................................................................................................. 3-28

Содержание REL-300








































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды