ABB REL-300 Скачать руководство пользователя | Manualshive

Страница: 17 / 135

background image

I.L. 40-385.1B

(5/92)

iii

Features Included in Version V2.00

The following features are

standard for the Non-Pilot MDAR V2.00:

• 3-Zone distance phase and ground relay, with re-

versible Zone 3 phase and ground; 4 impedance
units per zone: 3 phase-to-ground; 1 phase-to-
phase.

• Selectable Zone 1 extension

• • T1 timer (0 or 2 cycles)

• Independent timers for phase and ground (T2G,

T2P, T3G/T3P)

• • Block selection for T2 and T3 timers

• Inverse time directional or non-directional (select-

able) overcurrent ground backup logic

• Loss of potential supervision (LOP)

• Loss of current monitoring (LOI)

• Overcurrent supervision

• Instantaneous forward directional phase and

ground highset overcurrent trip (ITP and ITG)

• Close Into Fault Trip (CIFT)

• • Stub Bus Protection (89b)

• Unequal-pole-closing load pickup logic

• • Selectable Loss-of-Load accelerated trip logic

(LLT)...setting (YES/NO/FDOG)

• Current change fault detector (

∆

I)

• Voltage change fault detector (

∆

V)

• Last Fault LED now blinks once for a single fault

and twice for more than one fault. When the RE-
SET button is depressed, the flashing LED is re-
set, and the displayed data is returned to the
green LED (i.e., Volts/Amps/Angle...metering
mode). MDAR fault data cannot be cleared out of
memory from the front panel. Fault data can be
re-accessed by moving the LED down to the Last
Fault or Previous Fault.

• Line voltage, current and phase angle monitor.

• • Selectable polarizing for directional O/C ground

units (ZSEQ/NSEQ/DUAL)

• Programmable Reclose initiation and reclose

block (RB) outputs; Reclose Initiate (RI2) can be

enabled with the selection of:

– 1PR for

φ

G fault

– 2PR for

φ

G or

φφ

fault

– 3PR for

φ

G or

φφ

fault or 3

φ

fault

• Digital Processing

• Fault locator software

• Self-checking software shows error codes

• Breaker trip circuit test

• • Push-to-close test for output contacts

• Software switches for functional tests, e.g., TK

(Carry Send Switch), RS1, RS2 and RS12 (Carry
Receivers).

• • Trip contact sealed in by trip current; and select-

able dropout delay timer, 0/50, (YES/NO)

• • 16 fault records (triggered by TRIP, Z2PU or

Z2Z3)

• Real-time clock

• Low voltage pickup setting (LV) for weakfeed log-

ic and CIF trip; selection can be made from 40
Vrms to 60 Vrms, in 1-volt steps.

• Setting of ZR, range from 0.1 to 7.0

• Setting of XPUD, range from 0.3 to 1.5 per mile or

per km

• Setting of FDAT (trip, Z2 trip or Z2Z3 trip)

• Logic for load restrictions

• The reaches of Z1E are based on Zone 1 settings

multiplied by a factor of 1.25 (e.g., 1.25 x Z1P and
1.25 x Z1G).

NOTE: The foregoing (and following) features preceded by two dots (• •) were not included in V1.65.

«
...
15
16
17
18
19
...
»

Содержание REL-300








































































































































Отзывы:

Нет отзывов

Похожие инструкции для REL-300

Бренд: VAMP Страницы: 186

Бренд: OEZ Страницы: 6

Бренд: Toshiba Страницы: 8

Бренд: Toshiba Страницы: 25

Бренд: Toshiba Страницы: 20

Бренд: Toshiba Страницы: 40

Бренд: Toshiba Страницы: 16

Бренд: Toshiba Страницы: 20

Бренд: Toshiba Страницы: 12

Current Relay RC803A-HP1

Бренд: Toshiba Страницы: 19

Бренд: Toshiba Страницы: 22

Бренд: Toshiba Страницы: 392

GRZ100 B Series

Бренд: Toshiba Страницы: 447

Бренд: Toshiba Страницы: 183

GRL150-100 Series

Бренд: Toshiba Страницы: 267

Бренд: Pilz Страницы: 19

Бренд: Pilz Страницы: 16

Бренд: Pilz Страницы: 69

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды