ABB PVS-175-TL-US Скачать руководство пользователя страница 7

Страница: 7 / 44

—

Models and range of equipment

PVS-100/120-TL “B version” - Communication board (28)

The choice of the inverter model must be made by a qualified technician who knows about the installation condi-

tions, the devices that will be installed outside the inverter and possible integration with an existing system.

“Wiring box” Model Number

Description

PVS

WB-SX-PVS-166-TL-US

WB-SX-PVS-175-TL-US

•  24 quick fit connector pairs (2 each MPPT)
•  DC switches
•  SPD Type 2 Pluggable Cartridges (DC & AC)

WB-SX2-PVS-166-TL-US

WB-SX2-PVS-175-TL-US

•  24 quick fit connector pairs (2 each MPPT)
•  DC switches
•  AC disconnection switch
•  SPD Type 2 Pluggable Cartridges (DC & AC)

“Power module” Model Number

Description

PVS

PVS-166-TL-POWER MOD-

ULE

Inverter section / power module with 166kW output power

PVS-175-TL-POWER MODULE

Inverter section / power module with 175kW output power

“Bracket” Model Number

Description

PVS-175-TL-BRACKET

Bracket allowing vertical installation only.

J10

J20

Содержание PVS-175-TL-US













































Результаты поиска

Содержание PVS-175-TL-US

Отзывы:

ABB PVS-175-TL-US, Быстрое руководство по установке, Страница: 7 / 44

Результаты поиска

Содержание PVS-175-TL-US

Отзывы: