ABB OmniCore V400XT Скачать руководство пользователя страница 365

Страница: 365 / 466

7.2.10 Controller is overheated

Required test equipment

Equipment needed for troubleshooting:

Note

Equipment

Multimeter

Insulating gloves

3HAC082020-008

Circuit diagram - OmniCore V400XT

Preparations

Action

Make sure that the controller is switched on.

Wait 30 s - 1 min to enable start-up sequence.

Check the FlexPendant for errors and warnings.

DANGER

Troubleshooting on the controller while powered on must be performed by personnel
trained by ABB or by ABB field engineers.

Recommended working procedure

If the controller seems to be overheated, use this procedure to troubleshoot what
might cause the problem.

Detailed working procedure

Note

Action

Replace malfunctioning fans, see

Replacing the external fans on
page 188

Check that the external fans are working.

Replace malfunctioning fans, see

Replacing the internal fan on
page 192

Check that the internal fan is working.

Replace malfunctioning fans, see

Replacing the power unit fan on
page 200

Check that the power unit fan is working.

If air filters are not clean, see

Cleaning air filter on page 161

Inspect the air filters to make sure they are clean.

If air filters need to be replaced,
see

Replacing the air filter on

page 277

See

Troubleshooting the power

unit on page 381

and

Troubleshoot-

ing the drive unit on page 368

If the problem remains, troubleshoot the power
unit and/or the drive unit.

Product manual - OmniCore V400XT

365

3HAC081697-001 Revision: A

7 Troubleshooting

7.2.10 Controller is overheated

Содержание OmniCore V400XT


















































































































































































































































































































































































































































































Результаты поиска

Содержание OmniCore V400XT

Отзывы:

Похожие инструкции для OmniCore V400XT

Бренды по названию

Популярные бренды

ABB OmniCore V400XT, Руководство по эксплуатации продукта

Результаты поиска

Содержание OmniCore V400XT

Отзывы:

Похожие инструкции для OmniCore V400XT

Бренды по названию

Популярные бренды