background image

1.7 Safety during maintenance and repair

General

Corrective maintenance must only be carried out by personnel trained on the robot.

Maintenance or repair must be done with all electrical, pneumatic, and hydraulic
power switched off, that is, no remaining hazards.

Never use the robot as a ladder, which means, do not climb on the controller,
manipulator, including motors, or other parts. There are hazards of slipping and
falling. The robot might be damaged.

Make sure that there are no tools, loose screws, turnings, or other unexpected
parts remaining after maintenance or repair work.

When the work is completed, verify that the safety functions are working as
intended.

Hot surfaces

Surfaces can be hot after running the robot, and touching these may result in burns.
Allow the surfaces to cool down before maintenance or repair.

Hazards related to batteries

Under rated conditions, the electrode materials and liquid electrolyte in the batteries
are sealed and not exposed to the outside.

There is a hazard in case of abuse (mechanical, thermal, electrical) which leads
to the activation of safety valves and/or the rupture of the battery container. As a
result under certain circumstances, electrolyte leakage, electrode materials reaction
with moisture/water or battery vent/explosion/fire may follow.

Do not short circuit, recharge, puncture, incinerate, crush, immerse, force discharge
or expose to temperatures above the declared operating temperature range of the
product. Risk of fire or explosion.

Operating temperatures are listed in

Operating conditions on page 39

.

See safety instructions for the batteries in

Material/product safety data

sheet - Battery pack

(

3HAC043118-001

).

Related information

See also the safety information related to installation and operation.

32

Product manual - OmniCore V400XT

3HAC081697-001 Revision: A

© Copyright 2022-2023 ABB. All rights reserved.

1 Safety

1.7 Safety during maintenance and repair

Содержание OmniCore V400XT



















































































































































































































































































































































































































































































Отзывы: