ABB MegaFlex UL S1 Series Скачать руководство пользователя

Страница: 57 / 86

57/86

MegaFlex 1000 to 1600

UPS User Manual / REV-A

7.1.2

Complete UPS shut-down

Note!
Follow this procedure only in case the UPS system and the Load must be completely powered-

down.

If eBoost™ option is available, make sure that eBoost™ Operation Mode is disabled before starting
this procedure.

Initial status:

Load supplied by Inverter.

1. Perform the command

“

System shutdown”.

Perform the command “System shutdown” through

the screen:

Commands 1 / System shutdown /

SHUTDOWN

•

Load is disconnected from UPS.

•

Rectifier and Inverter are shut down and all contactors are
opened.

•

LED 1 (Rectifier) and LED 2 (Inverter) are OFF.

•

LED ALARM is lit.

2. Open the “Q1 – External UPS Output Circuit Breaker” (Pos. O).

3. Disconnect the Battery from the UPS by opening the “External Battery Breaker” (Pos. O).

Note!

Before performing the next procedure

(4) wait 5

minutes for DC-link Capacitors discharge.

Use the MEASURES/Rectifier screen to ensure that

the DC-link 1 and DC-link 2 voltage has reached
10Vdc.

Press “MUTE” key to reset Acoustical Alarm.
LED ALARM remains lit.

4. Disconnect the Utility from the input distribution.

End of Procedure

Danger!
It will take 5 minutes for the DC capacitors to discharge.
Open only the front door, do not open any other part of the UPS.

Содержание MegaFlex UL S1 Series























































































Результаты поиска

Содержание MegaFlex UL S1 Series

Отзывы:

Похожие инструкции для MegaFlex UL S1 Series

Бренды по названию

Популярные бренды

ABB MegaFlex UL S1 Series, Руководство пользователя

Результаты поиска

Содержание MegaFlex UL S1 Series

Отзывы:

Похожие инструкции для MegaFlex UL S1 Series

Бренды по названию

Популярные бренды