ABB MegaFlex UL S1 Series Скачать руководство пользователя

Страница: 75 / 86

75/86

MegaFlex 1000 to 1600

UPS User Manual / REV-A

Note!
Ensure the LED 1 (Rectifier) is lit before carrying out this procedure (3).
It indicates that the DC-link 1 and DC-link 2 has reached 400Vdc (see screen MEASURES /

Rectifier)!

3. Connect the Battery to the Unit to reconnect by closing the “External Battery Breaker” (Pos. I).

Synoptic diagram of the unit to reconnect

Synoptic diagram of other units

Note!
Before performing the next procedure (4) make sure that the LED 3 (Booster/Battery charger)

is lit.

4. Insert the Inverter performing the command "Inverter ON” on the Unit to reconnect.

Perform the “Inverter ON” command from the screen:
Commands 1 / Inverter /

•

After Soft-start of the Inverter the Inverter connects automatically to the other Units of the RPA Parallel
System.

•

LED ALARM turns OFF and the LED LOAD PROTECTED must be lit.

The Synoptic Diagram, on all UPS units, must display the status “

Load supplied by Inverter

”.

Synoptic diagram of the unit to reconnect

Synoptic diagram of other units

End of Procedure

Содержание MegaFlex UL S1 Series























































































Результаты поиска

Содержание MegaFlex UL S1 Series

Отзывы:

Похожие инструкции для MegaFlex UL S1 Series

Бренды по названию

Популярные бренды

ABB MegaFlex UL S1 Series, Руководство пользователя

Результаты поиска

Содержание MegaFlex UL S1 Series

Отзывы:

Похожие инструкции для MegaFlex UL S1 Series

Бренды по названию

Популярные бренды