manualshive.com logo in svg

ABB MegaFlex UL S1 Series, Руководство пользователя

Поделиться
Скачать
ABB MegaFlex UL S1 Series Скачать руководство пользователя страница 36

36/86

 

MegaFlex 1000 to 1600

     UPS User Manual / REV-A

 

 
 

 

Code 

Alarm 

Description 

4421 

K3 OPENING FAILURE 

K3 not open despite an opening command. 
Be aware the DC Capacitors could remain charged. 

4520 

NO INVERTER POWER 

The Load supplied by Utility exceeds the Inverter power. 
The Load remains supplied by Utility until the alarm stays ON. 

4522 

FAN FAILURE 

The  Fan Control Board indicates a malfunction of one or 
more ventilators. 

4530 

LOAD LOCKED ON UTILITY 

Load  is locked on Utility because 3 transfers on Utility have 
been detected in a short time (default 30 sec.). 
The transfer will be free after a time defined in parameter 
(default 30 sec.). 

4531 

LOAD ON UTILITY BY ERROR 
DETECTOR 

Load  is transferred to Utility  because the error detector 
detected a disturbance on the output voltage. 

4563 

EMERGENCY OFF ACTIVATED 

Alarm after detection of an EPO (Emergency Power Off) from 
an external safety device connected on Customer Interface 
Board. Consequently K4, K6, K7 open, Rectifier,  Inverter and 
SSM are switched Off. 

4570 

OVERLOAD 

The UPS system is in an overload condition 

>

105% on 

Inverter, or 

>

150% on Utility. 

With  Utility  unavailable, a sequence of “stop operation” 
starts. Time out depends on degree of overload. 

4571 

OVERLOAD: LOAD ON UTILITY 

With  Utility Bypass  supply available and Load 

>

115%, the 

Load is transferred on Utility. Load will be transferred again 
automatically on Inverter when Load 

<

100%. 

4581 

INVERTER AND UTILITY 
NOT SYNCHRONIZED 

The voltages of Utility  and  Inverter  are not synchronized, 
which causes the opening of K6. 

4608 

ECO CONFIG FAILURE 

The propagation of the eBoost™ configuration to other units 
in an RPA Parallel System failed. 

4681 

MAIN BOARD BATTERY CHANGE 
NEEDED 

Notice to replace the Lithium Battery located on the Control 
Board. 

4682 

DC CAPACITORS CHANGE NEEDED 

Notice to replace the DC Capacitors. 

4683 

AC CAPACITORS CHANGE NEEDED 

Notice to replace the AC Capacitors. 

4684 

FAN REPLACEMENT NEEDED 

Notice to replace the Fans. 

4685 

SERVICE MAINTENANCE OVERDUE 

Notice to do the Service Maintenance. 

4697 

BATTERY OVERTEMPERATURE 

Detection of Battery overtemperature condition. 
Only an ABB Service Technician can reset the alarm. 

4698 

BATTERY POWER INSUFFICIENT 

In case of Utility Failure, with the actual Load, the run time 
would be below stop operation time (default 3 minutes). 

4700 

DC LOW 

Battery voltage is at the lowest limit. 
Inverter will remain Off until the Battery voltage reaches the 
value in parameter. 

4701 

POWER SUPPLY BOARD FAILURE 

Detection of a failure on the Power Supply Board, in 
particular from the DC supply. 
Can be enabled or disabled with respective parameter. 

4702 

LOSS OF REDUNDANCY 

A time of lost redundancy superior than specified in 
respective parameter was detected. 

4900 

LOAD LOCKED ON INVERTER 

The Load is locked on Inverter after 3 Load transfers within 
30 seconds.  
After time out (default 30 sec.) Bypass will be free. 

4955 

OVERTEMPERATURE 

An overtemperature condition has been detected on Inverter. 
Elapsed “stop operation” time, Inverter shut-down. 
With Utility OK, Load is transferred on Utility. 

4998 

LOAD OFF DUE TO EXTENDED 
OVERLOAD 

Load Off after time-out of “stop operation” for overload on 
Inverter (time depending on the % of overload). 

4999 

LOAD OFF DUE TO LOW BATT. OR 
TEMP. 

Load Off  after time-out of “stop operation”  with missing 
Utility  due to Battery  low voltage or overtemperature 
condition. 

 

 

Содержание MegaFlex UL S1 Series























































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды