ABB MegaFlex UL S1 Series Скачать руководство пользователя | Manualshive

Страница: 34 / 86

background image

34/86

MegaFlex 1000 to 1600

UPS User Manual / REV-A

Code

Alarm

Description

4105

RECTIFIER OVERTEMPERATURE

Temperature sensor indicates a situation of
overtemperature on the Rectifier bridge.
Only the alarm is given.
The Rectifier, when in an Off state, cannot start as long as
this condition persists.

4106

RECTIFIER TRANSFORMER
OVERTEMPERATURE

The temperature sensor inside the input transformer
winding indicates overtemperature.
Only the alarm is given.
The Rectifier, when in an Off state, cannot start as long as
this condition persists.

4110

RECTIFIER UTILITY OUT OF TOLERANCE

Rectifier Input Utility is out of tolerance (voltage, frequency
or phase sequence).

4115

LOW BATTERY VOLTAGE

The Battery has been discharged and reached “stop
operation” time-out (default 3 minutes) and the Inverter will
be shut down.
It will restart automatically only when the Battery has
recharged enough for a minimum runtime.

4116

HIGH BATTERY VOLTAGE

Dangerous high DC Voltage caused Inverter shut-down.
Inverter restarts automatically after Battery returns to
floating voltage.

4117

BATTERY EARTH FAULT

A leakage current to earth has been detected on the DC
circuit.

4118

BATTERY FAULT

During Battery test the voltage falls under the critical level
(depending setting parameters).
Battery test is stopped.

4121

HIGH DC RIPPLE

A high ripple is present in the Battery voltage.

4125

HIGH DC-LINK VOLTAGE

Detection of high voltage on the DC-link.
The Rectifier, Booster and Inverter will switch off for
protection purposes.
The Rectifier may only be switched on again if the DC-link’s
voltage value falls below 430Vdc.

4126

4

th

LEG CONTROL SATURATION (Imax)

The current in the fourth leg has reached its highest value.

4130

TURN ON RECT. OR SHUTDOWN UPS

Rectifier and Inverter are OFF.
The DC power supply is discharging the Battery.
Rectifier must be restarted, or the Battery must be
disconnected in order to avoid damage.

4140

RECTIFIER CONTROL FAILURE

Rectifier Voltage hasn’t reached the set value (probably
fault on regulation loop).
LED Rectifier on Control Panel is blinking.

4141

ISMAX DETECTION RECTIFIER

After 3 IS-Max condition within the time frame specified in
respective parameter, the Rectifier remains shut-down.

4142

RECTIFIER CURRENT MAX

Will cause immediate shut-down of the Rectifier.
Based on the value inserted in the respective parameter.

4143

BOOSTER/BATTERY CHARGER
CURRENT MAX

Detection of maximum current in the Booster/Battery
charger.
The Booster/Battery charger and Inverter will switch off for
protection purposes.

4146

4TH LEG DRIVER FAILURE

The Booster’s driver indicates the presence of a defect
which switches the power off.

4147

BATTERY CHARGER DRIVER FAILURE

The Battery charger driver indicates a defect, switching it
off.

4150

BOOSTER OVERTEMPERATURE

The temperature of the Booster bridge exceeds the
machine’s set limit or the coil’s sensor is on.

4151

4TH LEG OVERTEMPERATURE

The temperature of the 4

th

leg’s bridge exceeds the

machine’s set limit.

«
...
32
33
34
35
36
...
»

Содержание MegaFlex UL S1 Series























































































Отзывы:

Нет отзывов

Похожие инструкции для MegaFlex UL S1 Series

Бренд: Eaton Страницы: 27

IntelliQ Series

Бренд: Su-Kam Страницы: 16

Бренд: Always On Страницы: 14

Бренд: Fenton Страницы: 25

SANUPS E11A202U

Бренд: Sanyo Denki Страницы: 47

Бренд: SmartPower Страницы: 9

RIMATRIX5 PMC12

Бренд: Rittal Страницы: 5

Бренд: Sola Страницы: 26

Liebert GXT2 700

Бренд: Emerson Страницы: 8

Бренд: Emerson Страницы: 2

Бренд: Emerson Страницы: 2

Бренд: Njoy Страницы: 17

T90 Online 700VA

Бренд: Xtreme Страницы: 27

Бренд: Trust Страницы: 49

Бренд: Shield Страницы: 84

Бренд: Speco Страницы: 1

Бренд: Speco Страницы: 1

Бренд: Ferrups Страницы: 44

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды