ABB CMS-700 Скачать руководство пользователя страница 16

Страница: 16 / 65

CMS-700 SYSTEM

CIRCUIT MONITORING SYSTEM (CMS)

Pushbutton

Solid-core sensor

Open-core sensor

CMS-Bus

LED

Opening for the electrical

conductor

LEDs

Reset button

Terminal RS-485

Modbus (RTU)

CMS-Bus up to 96 sensors

RJ45-socket for LAN

connection

Terminals L1, L2, L3, N
• Wire gauge max 2.5 mm

• Voltage 80-277 VAC 50/60 Hz

Terminal Current Transformer

for secondary winding,

nominal 5 A, max 6 A

—

Control Unit

—

CMS Sensor

—

Components of CMS system

Sensor LED Status:

ON
Sensor is online and in measurement mode. There is a feature in the configuration
to switch off the LED after a specified time

OFF
Sensor is not connected to CMS-Bus or is switched off in the configuration

Flashing slowly
Sensor is not assigned

Flashing fast
Sensor in assign process or in "setting/branches" mode. This sensor is the sensor
corresponding to the yellow-marked row on the screen for webserver settings.

Содержание CMS-700


































































Результаты поиска

Содержание CMS-700

Отзывы:

Бренды по названию

Популярные бренды

ABB CMS-700, Руководство пользователя

Результаты поиска

Содержание CMS-700

Отзывы:

Бренды по названию

Популярные бренды