ABB AKD6-800A Скачать руководство пользователя | Manualshive

Страница: 15 / 47

background image

13

EntelliGuard R Circuit Breaker Retrofill AKD-6 Installation Manual DEH-41548 07/15

Figure 5. AKD-6 Compartment Distinctions

is an example of a compartment in the AKD-6 switchgear that is empty; that is, the upper compartment is

ready for a retrofill breaker where the legacy, or original breaker, had been racked out and new wire connections
made. The lower compartment has a retrofill breaker, already installed. In this figure, there is also a photo showing
a mechanically-operated status indicator (connect/disconnect) that worked with the original breaker. This device, if
left in the compartment as is, won’t interfere with the retrofill breaker; it can, however, be disassembled by
removing its hardware.

displays the bus inside the gear.

Figure 6. AKD6 Breaker Compartment (Upper and Lower Compartments)

«
...
13
14
15
16
17
...
»

Содержание AKD6-800A
















































Отзывы:

Нет отзывов

Похожие инструкции для AKD6-800A

Бренд: nader Страницы: 39

Cutler-Hammer Digitrip RMS 810

Бренд: Eaton Страницы: 32

Бренд: Eaton Страницы: 26

Бренд: CBS ArcSafe Страницы: 8

Бренд: CBS ArcSafe Страницы: 39

Бренд: ABB Страницы: 271

Бренд: ABB Страницы: 16

Бренд: ABB Страницы: 311

Sace Emax UL Listed

Бренд: ABB Страницы: 135

NZM XBSM Series

Бренд: Eaton Страницы: 5

MicroVersaTrip AKR-75

Бренд: GE Страницы: 102

Бренд: Comelit Страницы: 4

Бренд: ETC Страницы: 44

Бренд: Cooper safety Страницы: 76

Бренд: Eaton Страницы: 4

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды