ABB 1ZSC902110-AAA Скачать руководство пользователя

Страница: 8 / 84

Installation and commissioning guide

1ZSC000563-AAF EN, REV. 4, 2021-06-23

Terminal system

The bushing can be configured with one of two terminal systems: the fixed bottom contact system, or the
draw-rod system.

Terminal system

Option

Draw-rod system

Small bottom contact (N1=4)

Large bottom contact (N1=6)

Fixed bottom contact

Draw-rod system

The draw rod can be configured with an optional joint (53) to fit transformers with short bushing turrets.

The bottom-contact joint (56) is locked with threadlocking fluid as standard.

The bushing has draw rod with two upper joints (52), they are always locked with threadlocking fluid. All
joints must be locked with threadlocking fluid when the bushing is in operation at site.

G006981

39 Lower joint (at flange level).

52 Upper joint.

53 Additional joint (option).

54 Thread is locked with threadlocking fluid.

55 Thread is NOT locked with threadlocking fluid.*

56 Bottom-contact joint, locked with threadlocking fluid. Unlocked as option.*

* All unlocked threads must be locked with threadlocking fluid, when the bushing is installed at site.

Fixed bottom contact

The fixed bottom contact is installed when it is delivered from Hitachi ABB Power Grids.

CAUTION!

Do not remove the six fixing bolts.

Содержание 1ZSC902110-AAA





















































































Результаты поиска

Содержание 1ZSC902110-AAA

Отзывы:

Похожие инструкции для 1ZSC902110-AAA

Бренды по названию

Популярные бренды

ABB 1ZSC902110-AAA, Руководство по установке и пусконаладке

Результаты поиска

Содержание 1ZSC902110-AAA

Отзывы:

Похожие инструкции для 1ZSC902110-AAA

Бренды по названию

Популярные бренды