ABB 1ZSC902110-AAA Скачать руководство пользователя

Страница: 16 / 84

Installation and commissioning guide

1ZSC000563-AAF EN, REV. 4, 2021-06-23

Remove the support blocks from the transport box and put them on the ground.

CAUTION!

Make sure that the ground is flat.

Install the lifting tool (88) on the flange.

G007208

Attach a soft lifting sling to the lifting tool (88) on
the lower part of the flange and then to the crane
hook.

G006950

Attach a soft lifting sling to the top part of the
porcelain insulator.

CAUTION!

Attach the soft lifting sling as close to
the top housing as possible, or damage
will occur.

G006951

Carefully lift the bushing.

Make sure that the support blocks are in the same positions as the support blocks in the
transport box.

Содержание 1ZSC902110-AAA





















































































Результаты поиска

Содержание 1ZSC902110-AAA

Отзывы:

Похожие инструкции для 1ZSC902110-AAA

Бренды по названию

Популярные бренды

ABB 1ZSC902110-AAA, Руководство по установке и пусконаладке

Результаты поиска

Содержание 1ZSC902110-AAA

Отзывы:

Похожие инструкции для 1ZSC902110-AAA

Бренды по названию

Популярные бренды