ABB 1ZSC902110-AAA Скачать руководство пользователя

Страница: 6 / 84

Installation and commissioning guide

1ZSC000563-AAF EN, REV. 4, 2021-06-23

1.2 Hazardous working situations

Hazard

Action

Working close to high voltage.

Disconnect all plant power. Ground all objects at the workplace.

If work must be done close to live plant components, make sure that
the safety distance is in compliance with the applicable safety
regulations.

Working on ladders and platforms.

Work must be done in accordance with the applicable safety
regulations.

Do not use ladders or platforms in poor weather conditions.

Working with heavy objects.

Do not walk under lifted objects.

Make sure that heavy objects are stable before starting work.

1.3 Safety precautions

Precaution

Action

Transformer oil

Collect used transformer oil in drums.

Transformer oil is dangerous. Fumes from hot oil can cause irritation
to the respiratory organs and the eyes. Long and repeated contact
with transformer oil can cause damage to your skin.

Waste and cleaning up

Clean up liquid waste with an adsorbent. Treat waste as hazardous
to the environment.

Fire

Extinguish fires with powder, foam or carbon dioxide.

1.4 Competence level

Installation of the bushing should only be performed by authorized personnel.

CAUTION!

Incorrect installation can lead to catastrophic failure of the transformer.

Содержание 1ZSC902110-AAA





















































































Результаты поиска

Содержание 1ZSC902110-AAA

Отзывы:

Похожие инструкции для 1ZSC902110-AAA

Бренды по названию

Популярные бренды

ABB 1ZSC902110-AAA, Руководство по установке и пусконаладке

Результаты поиска

Содержание 1ZSC902110-AAA

Отзывы:

Похожие инструкции для 1ZSC902110-AAA

Бренды по названию

Популярные бренды