ABB 1ZSC902110-AAA Скачать руководство пользователя

Страница: 23 / 84

Installation and commissioning guide
1ZSC000563-AAF EN, REV. 4, 2021-06-23

Carefully lift the bushing from the floor.

CAUTION!

Make sure that the bushing does not
rotate.

G007349

Lift the bushing up from the floor with both cranes.

Lift the upper part of the bushing. Stop when
the bushing is in a vertical position.

Remove the lower soft lifting slings to the
crane.

Remove the flange lifting tool (88).

CAUTION!

Do not let the bushing come in contact
with the floor while raising the bushing
to a vertical position. Contact with the
floor can cause damage to the
bushing.

G007350

Lift the bushing to a position above the transformer.

CAUTION!

Make sure that the bushing does not rotate.

Align the bushing with the hole in the transformer turret.

End of instruction

Содержание 1ZSC902110-AAA





















































































Результаты поиска

Содержание 1ZSC902110-AAA

Отзывы:

Похожие инструкции для 1ZSC902110-AAA

Бренды по названию

Популярные бренды

ABB 1ZSC902110-AAA, Руководство по установке и пусконаладке

Результаты поиска

Содержание 1ZSC902110-AAA

Отзывы:

Похожие инструкции для 1ZSC902110-AAA

Бренды по названию

Популярные бренды