manualshive.com logo in svg

AAON RQ SERIES, Установка, эксплуатация и обслуживание, Страница: 79 / 100

Поделиться
Скачать
AAON RQ SERIES Скачать руководство пользователя страница 79

79 

surface preparation, the best work yields the 
best results. 
 
Apply  CHLOR*RID  DTS  -  Apply  directly 
onto  the  substrate.  Sufficient  product  must 
be applied uniformly  across  the substrate to 
thoroughly  wet  out  surface,  with  no  areas 
missed. This may be accomplished by use of 
a  pump-up  sprayer  or  conventional  spray 
gun. The method does not matter, as long as 
the entire area to be cleaned is wetted. After 
the  substrate  has  been  thoroughly  wetted, 
the  salts  will  be  soluble  and  is  now  only 
necessary to rinse them off. 
 
Rinse - It is highly recommended that a hose 
be  used,  but  a  pressure  washer  will  damage 
the fins. The water to be used for the rinse is 
recommended  to  be  of  potable  quality, 
though a lesser quality of water may be used 
if  a  small  amount  of  CHLOR*RID  DTS  is 
added. 

Check 

with 

CHLOR*RID 

International,  Inc.  for  recommendations  on 
lesser quality rinse water.

 

 

Microchannel Coil Cleaning

 

Air-cooled  heat  exchangers  may  include 
microchannel coils. 
 
Cleaning  microchannel  coils  is  necessary  in 
all  locations.  In  some  locations  it  may  be 
necessary  to  clean  the  coils  more  or  less 
often  than  recommended.  In  general,  a 
condenser  coil  should  be  cleaned  at  a 
minimum of once a year. In locations where 
there is commonly debris or a condition that 
causes  dirt/grease  build  up  it  may  be 
necessary  to  clean  the  coils  more  often. 
Proper  procedure  should  be  followed  at 
every  cleaning  interval.  Using  improper 
cleaning  technique  or  incorrect  chemicals 
will 

result 

in 

coil 

damage, 

system 

performance  fall  off,  and  potentially  leaks 
requiring coil replacement. 
 
Documented 

routine 

cleaning 

of 

microchannel  coils  with  factory  provided  e-
coating  is  required  to  maintain  coating 
warranty  coverage.  Use  the  E-Coated  Coil 

Cleaning  section  for  details  on  cleaning  e-
coated coils. 
 
Field  applied  coil  coatings  are  not 
recommended with microchannel coils. 
 

Allowed 

Chemical 

Cleaners 

and 

Procedures 

AAON  recommends  certain  chemicals  that 
can be used to remove buildup of grime and 
debris  on the surface of  microchannel  coils. 
These  chemicals  have  been  tested  for 
performance  and  safety  and  are  the  only 
chemicals  that  AAON  will  warrant  as 
correct for cleaning microchannel coils. 
 
There  are  two  procedures  that  are  outlined 
below  that  will  clean  the  coils  effectively 
without  damage  to  the  coils.  Use  of  any 
other  procedure  or  chemical  may  void  the 
warranty  to  the  unit  where  the  coil  is 
installed. 

With  all  procedures  make  sure 

the unit is off before starting.

 

 

 

 
The water pressure used to clean should not 
exceed 140 psi, from no closer than 6 inches 
from  the  coils,  and  with  the  water  aimed 
perpendicular to the coils. 
 

#1 Simple Green 

Simple Green is available from AAON Parts 
and  Supply  (Part#  T10701)  and  is 
biodegradable  with  a  neutral  6.5  pH. 
Recommendation is to use it at a 4 to 1 mix. 
Use the following procedure. 
1.

 

Rinse  the  coil  completely  with  water. 
Use  a  hard  spray  but  be  careful  not  to 
bend or damage the fins. A spray that is 
too  hard  will  bend  the  fins.  Spray  from 
the fan side of the coil. 

 

 

 
 

 

Electric  shock  hazard.  Shut  off  all 
electrical  power  to  the  unit  to  avoid 
shock  hazard  or  injury  from  rotating 
parts.

 

    

 

WARNING

 

Содержание RQ SERIES





































































































Отзывы:

Нет отзывов