Aanderaa 4330 Скачать руководство пользователя страница 22

Страница: 22 / 93

TD 269 OPERATING MANUAL

OXYGEN OPTODE 4330, 4831, 4835

June 2017

page 22 of 93

Sensor Configuration

After installing the sensor turn power on and open the

System Configuration

from the

Menu

button.

Select the newly installed

Oxygen Optode

which should appear in the list of sensors, and tap

Configure

in the lower part of the window.

The

System Configuration

holds a list of output parameters

that can be enabled/disabled by the user, refer Figure 3-2.

Enabled properties (

Yes

) are stored in the data logger:

•

Enable

Air Saturation in engineering units.

•

Enable

Raw data, refer chapter 2.2 .

•

Enable

Temperature in engineering units.

•

Enable HumidityComp

property activates compensation

of vapour pressure in the calculations of the output

parameters. Enable HumidityComp can be set to

measurements are performed in dry air conditions or if you

like to perform the humidity compensation as a post-

processing operation. Disabling this will typically lead to 1-3

% lower readings depending on the relative humidity of the

air.

The absolute oxygen level,

M, is a default parameter and cannot be disabled, refer TD262a.

To enable/disable a parameter:
Select the output parameter from the list, press

View/Edit

in the lower part of the window, and change the

setting by clicking the box (box is now checked), press

Save

to save and close the window.

We recommend that you enable all parameters in case of later use. The memory card storage capacity is

normally not a limitation for the SEAGUARD

. Raw data can be used e.g. to control calibration

coefficients and perform quality control on the data.

3.2 RedReference, Calibration Coefficients and Salinity Compensation

Special property settings and calibration coefficients are found in

User Maintenance

Open the

User Maintenance

from the

Menu

button. Select the

Oxygen Optode

from the list of sensors,

and tap

Configure

in the lower part of the window. The user maintenance holds four submenus:

•

Node Description

•

Salinity setting

•

Calibration Coefficients

•

Enable RedReference

Figure 3-2 System Configuration;

Output settings.

Содержание 4330






























































































Результаты поиска

Содержание 4330

Отзывы:

Бренды по названию

Популярные бренды

Aanderaa 4330, Руководство по эксплуатации

Результаты поиска

Содержание 4330

Отзывы:

Бренды по названию

Популярные бренды