A&D BM-5 Скачать руководство пользователя страница 45

Страница: 45 / 116

BM series

8.7.

Correcting the Internal Mass Value

The balance can correct the internal mass

value within the range shown below. This

function corrects the internal mass value to

conform to an external weight. The corrected

mass value is maintained in non-volatile

memory even if the AC adapter is removed.

The internal mass value is corrected as follows:

Model Correction

reference value Correction range

BM-5

BM-5D

5.00000 g

1.5 mg

BM-20

BM-22

20.00000 g

1.5 mg

BM-252

BM-200

BM-300

BM-500

200.0000 g

1.5 mg

Example

: With the

BM-300

, 200.0000 g is corrected by +0.6 mg (200.0006 g). When performing a

+0.6 mg correction with a 100 g external weight, the correction value will be +1.2 mg in
accordance with the reference value of 200 g.

1 Perform calibration using the internal mass. Weigh an external

weight and get the correction value.

2 Press

the

ON:OFF

key to turn the display off.

3 While pressing and holding the

key and the

RANGE

key,

press the

ON:OFF

key.

is displayed.

4 Press the

key to display the function switches. Set

the function table switch and internal mass correction switch
to "

" as shown to the right using the following keys.

RANGE

key..........To select the blinking digit.

RE-ZERO

key.......To change the value of the blinking digit.

key............To store the new value and return to the weighing mode.

CAL

key...............To cancel the current operation.

5 Press and hold the

RANGE

key (for approx. 2 seconds) to enter

the function table and release the key when

ba5fnc

is displayed.

6 Press

the

RANGE

key several times to display

7 Press

the

key.

Correct the internal mass value using the following keys.

RE-ZERO

(

)key....To increase the value.

MODE

(

)key ........To decrease the value.

key...........To store the new value and display the next

menu item of the function table.

CAL

key ............To cancel the current operation and display

the next menu item of the function table.

8 Press

the

CAL

key to return to the weighing mode.

9 Press the

CAL

key to calibrate the balance using the

internal mass.

10 Check that the correction has been performed properly with the

external weight. If the value is incorrect, repeat the correction.

Internal mass correction

Press and hold Press

Press and hold

(approx. 2 seconds)

Weighing

mode

Weighing mode

Function switches

Function table

Corrected value

Standby

Internal mass correction switch

Function table switch

Perform calibration

using the internal mass

200 g

Correct the internal mass

by +0.6 mg at 200 g.

Calibrate with this

internal mass

The same mass

200.0000

200.0006

Corrected value

Содержание BM-5





















































































































Результаты поиска

Содержание BM-5

Отзывы:

Бренды по названию

Популярные бренды

A&D BM-5, Инструкция по эксплуатации

Результаты поиска

Содержание BM-5

Отзывы:

Бренды по названию

Популярные бренды