A.O. Smith SGS - 100 страница 94 Скачать руководство пользователя

Страница: 94 / 121

Instruction manual SGS

S15 (blocking error)

Short circuit from

dummy 2

Short circuit in sensor

circuit

Replace the dummy sensor

(2)

To replace the necessary parts, you must contact your installation

engineer

S17 (blocking error)

Short circuit from

temperature sensor S

at the bottom of the

tank.

Short circuit in sensor

circuit

Replace the cable and/or sensor.

To replace the necessary parts, you must contact your installation

engineer

S18 (blocking error)

Short circuit from

temperature sensor S

in the collector.

Short circuit in sensor

circuit

Replace the cable and/or sensor.

To replace the necessary parts, you must contact your installation

engineer

F01 (blocking error)

Defect in power supply

circuit

Live and neutral

connected wrong way

around.

Be sure to connect the live and neutral correctly (3.11 "Electrically

connecting the water heater"); the water heater is phase-sensitive

See the electrical diagram (17 "Appendices").

Condensation on the

flame probe

1. Disconnect the lead at the flame probe
2. Ignite the water heater three times, with an interrupted

ionisation circuit

3. Reconnect the ionisation lead to the flame probe
4. Ignite the water heater again
5. The repeated ignition attempts will have caused the

condensation to evaporate

If errors persist, contact your installation engineer

Floating neutral

Install an isolating transformer (3.11.4 "Isolating transformer")

Contact your installation engineer to have an isolating transformer

installed

F02 (lock out error)

Fan fails to run at

correct speed.

Defective motor and/or

rotor.

1. Check the motor and rotor
2. Replace the fan if the motor or rotor is defective.
3. Reset controller

See the electrical diagram (17 "Appendices").

To have the wiring replaced and a new fan fitted, you must contact

your installation engineer

Code + description

Cause

Measure

Remark

Содержание SGS - 100


























































































































Результаты поиска

Содержание SGS - 100

Отзывы:

Похожие инструкции для SGS - 100

Бренды по названию

Популярные бренды

A.O. Smith SGS - 100, Инструкция по установке, эксплуатации и обслуживанию

Результаты поиска

Содержание SGS - 100

Отзывы:

Похожие инструкции для SGS - 100

Бренды по названию

Популярные бренды