manualshive.com logo in svg

A.O. Smith SGS - 100, Инструкция по установке, эксплуатации и обслуживанию

Поделиться
Скачать
A.O. Smith SGS - 100 Скачать руководство пользователя страница 8

Instruction manual SGS

5

Contents

1

Introduction   -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  9

1.1

About the water heater -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  - 9

1.2

What to do if you smell gas-  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  - 9

1.3

Regulations  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  - 9

1.4

Target groups  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -   10

1.5

Maintenance -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -   11

1.6

Notation conventions-  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -   11

1.7

Overview of this document -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -   12

2

Working principle of the water heater  -  -  -  -  -  -  -  -  -  -  -  -  -   13

2.1

Introduction  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -   13

2.2

General working principle of the water heater -  -  -  -  -  -  -  -  -  -  -  -  -  -  -   13

2.3

Water heater operating cycle -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -   15

2.4

Protection for the water heater  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -   16

2.5

Safety of the installation  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -   17

2.6

Protection for the solar heating system -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -   18

2.7

Safety of the solar heating system  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -   19

3

Installation  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -   21

3.1

Introduction  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -   21

3.2

Packaging -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -   21

3.3

Ambient conditions-  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -   21

3.4

Technical specifications  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -   23

3.5

Installation diagram   -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -   29

3.6

Unvented water connections -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -   30

3.7

Vented water connections  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -   30

3.8

Gas connection   -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -   31

3.9

Solar heating system-  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -   32

3.10

Air supply and chimney flue discharge  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -   32

3.11

Electrically connecting the water heater-  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -   38

3.12

Electrical connection of the solar heating system  -  -  -  -  -  -  -  -  -  -  -  -  -   42

3.13

Check the supply pressure, gas control valve pressure, CO

2

 value and 

switching pressure -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -   45

4

Conversion to a different gas category   -  -  -  -  -  -  -  -  -  -  -  -   53

4.1

Introduction  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -   53

5

Filling -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -   55

5.1

Filling unvented installations  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -   55

5.2

Filling vented installations   -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -   56

5.3

Filling solar heating system-  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -   56

6

Draining   -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -   59

6.1

Draining unvented installations -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -   59

6.2

Draining vented installations  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -   60

6.3

Draining solar heating system   -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -   60

gis

Содержание SGS - 100


























































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды