manualshive.com logo in svg

A.O. Smith SGS - 100, Инструкция по установке, эксплуатации и обслуживанию

Поделиться
Скачать
A.O. Smith SGS - 100 Скачать руководство пользователя страница 9

Contents

6

Instruction manual SGS

7

The control panel -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -   63

7.1

Introduction -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  - 63

7.2

Control  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  - 63

7.3

Explanation of icons-  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  - 63

7.4

ON/OFF switch on controller   -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  - 63

7.5

Navigation buttons   -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  - 63

7.6

PC connection   -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  - 64

8

Status of the water heater   -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -   65

8.1

Introduction -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  - 65

8.2

Operating modes  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  - 65

8.3

Error conditions -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  - 66

8.4

Service condition  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  - 67

8.5

Anode warning  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  - 67

8.6

Q/T Sensor warning -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  - 67

8.7

Collector temperature warning-  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  - 67

9

Starting the water heater  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -   69

9.1

Introduction -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  - 69

9.2

Starting the appliance -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  - 69

9.3

The appliance's heating cycle  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  - 69

10

Shutting down   -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -   71

10.1

Introduction -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  - 71

10.2

Decommissioning the water heater for a short period-  -  -  -  -  -  -  -  -  -  -  - 71

10.3

Isolating the water heater from the mains   -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  - 71

10.4

Decommissioning the water heater for a long period -  -  -  -  -  -  -  -  -  -  -  - 71

11

Main menu   -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -   73

11.1

Introduction -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  - 73

11.2

Notation convention for menu-related instructions  -  -  -  -  -  -  -  -  -  -  -  -  - 73

11.3

Switching to "ON mode" -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  - 73

11.4

Setting the water temperature -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  - 73

11.5

Week program   -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  - 74

11.6

Starting and stopping the week program -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  - 74

11.7

Changing the appliance's standard week program  -  -  -  -  -  -  -  -  -  -  -  -  - 74

11.8

Adding times to a week program-  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  - 76

11.9

Deleting times from a week program-  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  - 77

11.10

Extra period-  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  - 78

11.11

Settings-  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  - 79

12

Service program   -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -   81

12.1

Introduction -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  - 81

12.2

Setting the hysteresis -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  - 81

12.3

Displaying the error history   -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  - 81

12.4

Displaying the water heater history   -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  - 81

12.5

Display the selected water heater  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  - 82

12.6

Setting the service interval   -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  - 82

12.7

Service mode -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  - 82

12.8

Setting legionella prevention-  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  - 83

12.9

Solar heating system configuration   -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  - 83

12.10

Setting the central heating configuration -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  - 84

Содержание SGS - 100


























































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды