3D Systems PostCure 1050 Скачать руководство пользователя страница 59

Страница: 59 / 68

6. Slide the LED bracket into place.

7. Secure the bracket in place using the screws removed

earlier and a T10 driver. You do NOT need to tighten the inner

screws, as they are part of the light bar assembly and have

already been tightened by the manufacturer.

7.3 PostCure 1050 Remove-Replace Chamber Fan

If 3D Systems Service has instructed you during troubleshooting to replace a cooling fan, please follow this procedure to so.

CAUTION: Ensure that you have received the replacement cooling fan from 3D Systems, as it is the only

cooling fan that has been tested to work in the machine.

CAUTION: Ensure that you have removed the glass plate (to prevent breakage) before performing this

procedure.

There are four cooling fans in the curing chamber, one on each upper corner. They each have a plug-in power cable. The

upper-right fan (see below) at the front of the machine has an extra cable, which is for the thermistor mounted to the fan. The

fan in this position cannot be replaced by the fan with only a power cable.

3D Systems, Inc.

p/n 40-D177, Rev. A

Содержание PostCure 1050





































































Результаты поиска

Содержание PostCure 1050

Отзывы:

3D Systems PostCure 1050, Руководство пользователя, Страница: 59 / 68

Результаты поиска

Содержание PostCure 1050

Отзывы: