3Com Powerware Prestige Series Скачать руководство пользователя

Страница: 77 / 92

Powerware

Prestige Series Installation and Operator’s Manual for IBM Applications (3000 VA)

Uncontrolled Copy

C H A P T E R

ROUBLESHOOTING

The Prestige UPS is designed for durable, automatic operation and also
alerts you whenever potential operating problems may occur. Use the
following troubleshooting chart to determine the UPS alarm condition.

Unlit

Amber
Green
Flashing

Indicator Legend

Condition

Possible Cause

Action

UPS does not turn on.

UPS is not plugged in.

Plug UPS into working outlet.

Faulty wall socket.

Test wall socket, repair as required.

UPS input breaker is tripped.

Reduce load, then reset breaker.

Load does not turn on.

UPS has not been activated.

Press the Output

On button for one

second, then release.

UPS beeps occasionally.

Normal operation.

None. UPS is protecting your
equipment.

UPS input breaker trips.

Load fault.

Check the load.
Disconnect faulty load equipment.
Wait several minutes before resetting
the UPS input breaker.
Restart the load.

indicator remains

lit, even though line

Utility line is out of
specification.

Test wall socket, repair as required.

voltage is present.

UPS input breaker is tripped.

Reduce load, then reset breaker.

UPS does not provide
the expected backup
ti

Low battery capacity.

Allow battery to charge for 24 hours,
then retest.

time.

Protected equipment power
requirements exceed UPS
capacity.

Reduce load, then retest.

Содержание Powerware Prestige Series





























































































Результаты поиска

Содержание Powerware Prestige Series

Отзывы:

Похожие инструкции для Powerware Prestige Series

Бренды по названию

Популярные бренды

3Com Powerware Prestige Series, Инструкция по установке и эксплуатации

Результаты поиска

Содержание Powerware Prestige Series

Отзывы:

Похожие инструкции для Powerware Prestige Series

Бренды по названию

Популярные бренды