3Com Powerware Prestige Series Скачать руководство пользователя

Страница: 62 / 92

UPS Operation

Powerware

Prestige Series Installation and Operator’s Manual for IBM Applications (3000 VA)

Uncontrolled Copy

Press and hold the Output On button until the alarm beeps
again.

Two indicators, corresponding with the current setting, remain
flashing. The output voltage is factory-configured for 230V.

OVERLOAD
SITE FAULT
OVERTEMP
BATTERY
SELF TEST

220V

230V

240V

208V

Figure 18. Output Voltage Indicators

Press the Output

Off button to scroll through the output

voltage options, top to bottom. Each time you press the button,
the UPS beeps and the next two indicators flash.

NOTE

If you do not save a selection within two minutes, the setup automatically

aborts and switches back to the original configuration.

Press and hold the Output On button until the alarm beeps to
select and save the output voltage. Failure to release the button
immediately after the beep will cause the UPS to abort the
setup.

Continue to Step 10.

Plug the Y-cord of the PPDM into the power connectors on the
UPS as shown in Figure 17.

10.

Press and hold the Output On button until you hear the UPS
beep (approximately one second).

The

indicator remains lit and the Self Test indicator

turns on.

11.

Turn the Bypass switch on the PPDM to the NORMAL position.

The front panel displays the percentage of full load being
applied to the UPS. The UPS is now in Normal mode with the
load online.

Содержание Powerware Prestige Series





























































































Результаты поиска

Содержание Powerware Prestige Series

Отзывы:

Похожие инструкции для Powerware Prestige Series

Бренды по названию

Популярные бренды

3Com Powerware Prestige Series, Инструкция по установке и эксплуатации

Результаты поиска

Содержание Powerware Prestige Series

Отзывы:

Похожие инструкции для Powerware Prestige Series

Бренды по названию

Популярные бренды