background image

 

 

 

 

2016-07 
 
 
 
 
 
 

Acousto-Optic Modulator Driver  

Including:  Basic Modulator Alignment  
 
 

Instruction Manual

 

750c Series – Analog and Digital  
                       Dual Modulation  
                        

 

Key to model types :      

75o.C-m-ff

   

 

Base model features TTL buffer compatible modulation input level and 24/28Vdc supply. 

  

 

‘o’ indicates the base models standard frequency 

              

:  

40MHz 

 

 

 

80MHz 

 

 

 

110MHz 

 

 

 

150MHz 

 

 

 

200MHz 

 

 

 

250MHz 

 
 

 

‘C’ indicates case style 

 
 

and where appended,  

 
 

 

‘m’ indicates options  (combinations possible) 

 

 

 

2 Watt output 

 

 

 

3 Watt output 

 

 

 

4 Watt output 

 

 

 

6 Watt output 

 

 

 

  

 

 

 

+15V supply operation  

 
 

 

‘ff’ indicates non-standard frequency e.g. 

 

 

 

 

 

 

 

50 

50MHz 

 

 

 

120 

120MHz 

 

 

 

 

 
 

ISOMET CORP, 5263 Port Royal Rd, Springfield, VA 22151, USA. 

Tel:  +1 703 321 8301,  Fax: +1 703 321 8546,  e-mail: 

[email protected]

 

www.ISOMET.com

 

ISOMET (UK) Ltd, 18 Llantarnam Park, Cwmbran, Torfaen, NP44 3AX, UK.  

Tel: +44 1633-872721,  Fax: +44 1633 874678,  e-mail: 

[email protected]

  

ISOMET

 

Summary of Contents for 750c Series










Reviews: