CDC Elettromeccanica TX40, Manual

Page: 1 / 11

ELETTROMECCANICA CDC S.r.l - TX40 - MANUAL rev.2 - PAG. 1
T
X40
DIGITAL ELECTRONIC
MICROPROCESSOR
TIMER
MANUAL rev.2 11/2021
ELETTROMECCANICA CDC S.r.l
VIA TREVIGLIO 56/58
BRIGNANO GERA D'ADDA (BG)
TEL. +39 0363 382155
FAX +39 0363 382099
www.cdcelettromeccanica.it
vendite@cdcelettromeccanica.it
PREFACE
D D This manual contains the information necessary for
the product to be installed correctly and also instruc-
tions for its maintenance and use; we therefore recom-
mend that the utmost attention is paid to the following
instructions and to save it.
This document is the exclusive property of Elettromeccanica
CDC S.r.l. which forbids any reproduction and divulgation,
even partially, of the document, unless expressly authorized.
Elettromeccanica CDC S.r.l. reserves the right to make any
formal or functional changes at any moment and without any
notice.
Elettromeccanica CDC S.r.l. and its legal
representatives do not assume any responsibility for any
damage to people, things or animals deriving from violation,
wrong or improper use or in any case not in compliance with
the instrument features.
D D Whenever a failure or a malfunction of the device may
cause dangerous situations for persons, thing or animals,
please remember that the plant has to be equipped with
additional devices which will guarantee safety.
1. INSTRUMENT DESCRIPTION
1.1 General description
T X40 is a digital microprocessor timer, it offers the possibility
to program: up to 3 delay times (or Set Times), 5 operating
modes
for
OUT1
output,
5 operating modes
for
OUT2
output,
4 time scales
(allowing timings from 9999 hours max. to 0.01
s min.), 6 counting start modes and 2 counting modes ( UP
or DOWN ). The timer can also be equipped with an internal
or external buzzer
for signaling the end of the count.
The
4 digits display
normally
shows
the
counting status
while the outputs status is signalled by 2 LEDs . The instru-
ment has also 2 digital inputs for voltage-free contacts that
can be used for the count enabling ( CNT EN ) and Reset
(
RES
) commands and can have
up to 2 relay outputs
or
SSR for driving Solid State Relays
.
The instrument is programmed by using the 3 of the front
panel keys while the counting commands can be submitted
using the
-Start/Stop
or through the digital inputs
CNT
EN
and
RES
. The operating parameters configuration can
be done through keypad , A01 device connected to TTL port
(standard) or using NFC communication (optional).
Index
1. Instrument description ............................................... 1
1.1 General description ........................................................... 1
1.2 Front panel description ..................................................... 2
2. Programming ............................................................... 2
2.1 Fast Set Times programming ............................................ 2
2.2 Standard mode parameters programming ........................ 2
2.3 Parameter protection using a password ............................ 3
2.4 Customized mode parameter programming
(parameters programming level) ......................................... 3
2.5 Reset parameters to default value .................................... 3
2.6 Keyboard lock function ...................................................... 3
3. Usage warnings ........................................................... 4
3.1 Allowed Usage .................................................................. 4
4. Installation warnings ................................................... 4
4.1 Mechanical Mounting ........................................................ 4
4.2 Mechanical Dimensions [mm] ........................................... 4
4.2.1 Instrument dimensions ......................................................... 4
4.2.2 Panel cutout .......................................................................... 4
4.2.3 Mounting brackets ................................................................ 4
4.3 Electrical connections ....................................................... 4
4.3.1 Electrical connection diagram ............................................... 5
5. Operating mode ........................................................... 5
5.1 Display operation .............................................................. 5
5.2 Operation of the Counting commands .............................. 5
5.3 OUT1 Operating mode ...................................................... 6
5.4 OUT2 Operating mode ...................................................... 7
5.5 Internal buzzer operation .................................................. 8
5.6 Operation in case of power supply failure (backup) .......... 8
6. Accessories ................................................................. 9
6.1 Parameters configuration with A01 ................................... 9
6.2 Parameters configuration with AFC1 ................................ 9
7. Programmable parameters table .............................. 10
8. Problems and maintenance ...................................... 11
8.1 Cleaning .......................................................................... 11
8.2 Disposal .......................................................................... 11
9. Warranty and repairs ................................................. 11
10. Technical data ............................................................ 11
10.1 Electrical data ................................................................. 11
10.2 Mechanical characteristics .............................................. 11
10.3 Functional features ......................................................... 11
11. How to order .............................................................. 12