READ IT
OR
WATCH IT
Read instructions or watch easy-to-follow video.
Scan QR code or visit https://byjasco.com/53634i
53634
DUSK-TO-DAWN OUTDOOR
PLUG-IN TIMER
MOUNTING/INSTALLATION
1.
Mount the timer on a wall near a GFCI receptacle using a screw or nail.
Install timer as far above ground level as possible with receptacle
facing downward. Do not install where timer can be immersed or
where water will splash or drip onto receptacle. Screw or nail head
must extend at least 3/16in. from the wall (nail or screw not included).
2.
Hang the timer from the hole at the top of the unit.
SETUP
The built-in sensor automatically turns on at dusk and off at dawn.
1.
To test product, plug in and cover sensor. The light triggers
immediately and stays on until dawn. This test mode is only available
for the first time after being plugged in. Timer will have a 30-second
delay after initial test mode.
2.
Plug in the light or other device. If the connected device has a
switch, it must be in the ON position.
Note:
To ensure proper operation of the automatic function, ensure
the photocell sensor is shielded from all nighttime sources of light,
such as floodlights. Also, ensure the photocell sensor has direct
access to sunlight
Note:
Timer must sense light for at least 30 seconds to turn on after
sensing darkness.
Supplier Declaration of Conformity | Model #: 53634 | Jasco Products Co.,
10 E. Memorial Rd., Oklahoma City, OK 73114, www.byjasco.com
This device complies with Part 15 of the FCC and Industry Canada license-exempt RSS
standards. Operation is subject to the following two conditions: (1) this device may not
cause harmful interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation.
FCC NOTE:
The manufacturer is not responsible for any radio or TV interference
caused by unauthorized modifications to this equipment. Such modifications could
void the user’s authority to operate the equipment.
NOTE:
This equipment has been tested and found to comply with the limits for a Class
B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to
provide reasonable protection against harmful interference in a residential installation.
This equipment generates, uses and can radiate radio frequency energy, and if not
installed and used in accordance with the instructions, may cause harmful interference
to radio communications. However, there is no guarantee interference will not occur
in a particular installation. If this equipment does cause harmful interference to radio
or television reception, which can be determined by turning the equipment off and
on, the user is encouraged to try to correct the interference by one or more of the
following measures:
— Reorient or relocate the receiving antenna.
— Increase the separation between the equipment and receiver.
— Connect the equipment into an outlet on a circuit different from which the receiver
is connected.
— Consult the dealer or an experienced radio/TV technician for help.
CAN ICES-3(B)/NMB-3(B)
125VAC, 60Hz
10A 1250W general/resistive
5A 625W tungsten
1/4HP motor type 3R
Works with all LED and CFL bulbs
FCC/IC - EN
SPECIFICATIONS
RISK OF ELECTRICAL SHOCK
• PLUG DIRECTLY INTO A
GFCI PROTECTED OUTLET
• UNPLUG TIMER BEFORE
CLEANING
• FULLY INSERT PLUG
• KEEP AWAY FROM
CHILDREN
• NOT FOR WATER
IMMERSION
• SUITABLE FOR INDOOR
AND OUTDOOR LOCATIONS,
STORE INDOORS WHILE
NOT IN USE
RISK OF FIRE
• DO NOT USE TO CONTROL
APPLIANCES THAT CONTAIN
HEATING ELEMENTS
(COOKING APPLIANCES,
HEATERS, IRONS, ETC.)
• DO NOT EXCEED
ELECTRICAL RATINGS
• DO NOT USE IF DEVICE OR
CORD IS DAMAGED
• DO NOT USE WITH
EXTENSION CORDS
WARNING
MADE IN CHINA/HECHO EN CHINA
Distributed by Jasco Products Company LLC, 10 E. Memorial Rd., Oklahoma City, OK 73114.
This Jasco product comes with a 2-year limited warranty. Visit www.byjasco.com for
warranty details.
Questions? Contact our U.S.-based Consumer Care at 1-800-654-8483 between
7AM-8PM, M-F, Central Time.
©JASCO 2020 | 53634 | 09/18/20 v1
Power
MTS 53003
