ZyXEL Communications NWA-3166 User Manual Download Page 100 | Manualshive

Page: 100 / 332

background image

Chapter 8 Wireless Screen

NWA-3166 User’s Guide

100

SSID

The SSID (Service Set IDentifier) identifies the Service Set with which a wireless
station is associated. Wireless stations associating to the access point (AP) must
have the same SSID.

Normally, the ZyXEL Device acts like a beacon and regularly broadcasts the SSID
in the area. You can hide the SSID instead, in which case the ZyXEL Device does
not broadcast the SSID. In addition, you should change the default SSID to
something that is difficult to guess.

This type of security is fairly weak, however, because there are ways for
unauthorized wireless devices to get the SSID. In addition, unauthorized wireless
devices can still see the information that is sent in the wireless network.

Channel

A channel is the radio frequency(ies) used by IEEE 802.11a/b/g/n wireless
devices. Channels available depend on your geographical area. You may have a
choice of channels (for your region) so you should use a different channel than an
adjacent AP (access point) to reduce interference.

Wireless Mode

The IEEE 802.1x standard was designed to extend the features of IEEE 802.11 to
support extended authentication as well as providing additional accounting and
control features. Wireless Mode supports 802.11b/g, 802.11a, 802.11n/g and
802.11n/a.

MBSSID

Traditionally, you needed to use different APs to configure different Basic Service
Sets (BSSs). As well as the cost of buying extra APs, there was also the possibility
of channel interference. The NWA’s MBSSID (Multiple Basic Service Set IDentifier)
function allows you to use one access point to provide several BSSs
simultaneously. You can then assign varying levels of privilege to different SSIDs.

Wireless stations can use different BSSIDs to associate with the same AP.

The following are some notes on multiple BSS.

• A maximum of eight BSSs are allowed on one AP simultaneously.
• You must use different WEP keys for different BSSs. If two stations have

different BSSIDs (they are in different BSSs), but have the same WEP keys,

they may hear each other’s communications (but not communicate with each

other).

«
...
98
99
100
101
102
...
»

Summary of Contents for NWA-3166













































































































































































































































































































































Reviews:

No comments

Related manuals for NWA-3166

Brand: Lantronix Pages: 2

Brand: ADTRAN Pages: 2

Brand: D-Link Pages: 83

Brand: Fujitsu Pages: 46

BACnet UTY-VBGX

Brand: Fujitsu Pages: 103

Brand: Fujitsu Pages: 159

Brand: Gree Pages: 21

Brand: SpectraLink Pages: 15

Brand: Rotel Pages: 146

Brand: Mercury Pages: 5

Brand: Radio-tone Pages: 12

Brand: Xantrex Pages: 38

Communications gateway

Brand: Xantrex Pages: 70

Brand: Eyedro Pages: 2

Brand: Elesign Pages: 10

Brand: Technicolor Pages: 114

Brand: SmartRG Pages: 35

Brand: Telstra Pages: 34

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands