background image

7

 2.5.2 Connecti on to an electric roll-on shutt er

If the pool is fi tt ed with an electric roll-on shutt er, it can be connected to the chlorinator so that the chlorinator automati cally 

adapts its 

disinfectant  producti on when the shutt er is closed (see”3.1.2 “Low” mode”).

• 

Make sure 

that power to the appliance is disconnected at the supply source.

• 

Remove the silver protecti ve cover 

(

1

).

• 

Remove the 4 lower module fi xture screws and remove the module 

(

2

)

. The bott om of the electric board is now visible 

(called “PCB” on the diagrams below).

• 

If you have a water balance regulati on module, follow the installati on steps to reassemble the module (see the module’s 

installati on and user manual).

1

2

The chlorinator is compati ble with several diff erent types of electric shutt er. However, certain systems may not be 

compati ble. In those cases acti vate the “Low” mode manually using its specifi c butt on on the chlorinator control 

panel (see “3.1.2 “Low” mode”).

(1) = cell power supply

1

2

(2) = fl ow controller

(3) = shutt er connecti on

(4) = shunt

(5) = venti lator

(6) = 230V - 50Hz power supply

Shutt er with an end of run dry contact 

(

1

:

(shutt er closed = contact closed)

Shunt the left  hand “R/W” and “+15V” terminals, then connect the dry contact from the shutt er to the “BLK” and “0V” 

terminals (3).

Shutt er sending a closure signal

 (

2

)

 :

(shutt er closed = LV 12-24 V dc)

Connect the casing to the “BLK” terminal” and the positi ve (12-24 Vdc) to the left  “R/W” terminal (3).

Summary of Contents for TRi Series

















Reviews: