background image

21

  

5.2 I  Error code display

Display of

Possible causes

Solutions

Air temperature sensor fault

SD2 sensor is offline or incorrectly 

connected

 Sensor replacement

Deicing sensor fault

SD3 sensor is offline or incorrectly 

connected

 Sensor replacement

Low-pressure fault

Low pressure fault in the cooling 

circuit (if fault persists after 

acknowledgement)

 Call an approved technician

High-pressure fault

Air and water emulsion passed 

into the device 

Check the pool's hydraulic circuit

Insufficient water flow

Increase flow using by-pass, 

 

check that the pool filter is not clogged

Water temperature too high 

 

(32 °C maximum)

Wait until the temperature falls

Flow controller blocked

 Check the flow controller

Water condenser scaled up or 

blocked 

 Clean the water condenser

Outside temperature > 30°C and 

measured water temperature > 

30 °C

Close the bypass valve to increase the flow rate 

through the device

Water temperature sensor 

fault

SD1 sensor is offline or incorrectly 

connected

 Sensor replacement

Deicing cycle fault (>20 

minutes)*

Air temperature too low

Wait until the temperature is 

 

within the operating range

The evaporator is scaled up

Clean the evaporator (see § “4.2 I  

Maintenance”)

The ventilator does not work

 Replace the ventilator or the electronic 

board

Wrong value provided by the air 

 

or deicing sensor

 Replace the sensor.

* Error code not active on 

Defrost

 models.

EN

Summary of Contents for PI20 Series





























Reviews: