background image

7

are designated for the recovered refrigerant and labelled for that refrigerant (i.e. 

special cylinders for the recovery of refrigerant). Cylinders shall be complete with 

pressure-relief valve and associated shut-off valves in good working order. Empty 

recovery cylinders are evacuated and. if possible. cooled before recovery occurs.

• 

The recovery equipment shall be in good working order with a set of instructions 

concerning the equipment that is at hand and shall be suitable for the recovery 

of all appropriate refrigerants including, when applicable, flammable refrigerants. 

In  addition,  a  set  of  calibrated  weighing  scales  shall  be  available  and  in  good 

working order. Hoses shall be complete with leak-free disconnect couplings and in 

good condition. Before using the recovery machine, check that it is in satisfactory 

working order, has been properly maintained and that any associated electrical 

components are sealed to prevent ignition in the event of a refrigerant release. 

Consult manufacturer it in doubt.

• The recovered refrigerant shall be returned to the refrigerant supplier in the 

correct recovery cylinder, and the relevant waste transfer note arranged. Do not 

mix refrigerants in recovery units and especially not in cylinders.

• If compressors or compressor oils are to be removed. ensure that they have been 

evacuated to an acceptable level to make certain that flammable refrigerant does 

not remain within the lubricant. The evacuation process shall be carried out prior to 

returning the compressor to the suppliers. Only electric heating to the compressor 

body  shall  be  employed  to  accelerate  this  process.  When  all  is  drained  from  a 

system, it shall be carried out safely.

RECYCLING

This symbol means that your appliance must not be thrown into a normal bin. It will be selectively collected 

for the purpose of reuse, recycling or transformation. Any substances it may contain which are potentially 

dangerous to the environment shall be eliminated or neutralised. Request information on recycling procedures 

from your retailer.

EN

Summary of Contents for PI20 Series





























Reviews: