background image

     WARNING

A terminal bar marked "GROUND" is provided within the power center. To reduce the risk of electrical shock which 

can cause serious injury or death, connect this terminal bar to the grounding terminal of your electric service or 

supply panel with a continuous copper conductor having green insulation and one that is equivalent in size to the 

circuit conductors supplying this equipment, but no smaller than no. 12 AWG (3,3mm

2

). In addition, a second wire 

connector should be bonded with a no. 8 AWG (8,4mm

2

) copper wire to any metal ladders, water pipes, or other 

metal within five (5) feet (1,52 m) of the pool/spa. In Canada the bonding wire must be minimum 6 AWG (13,3mm

2

).

  WARNING

To avoid injury ensure that you use this control system to control only packaged pool/spa heaters which have built-

in operating and high limit controls to limit water temperature for pool/spa applications. This device should not be 

relied upon as a safety limit control.

  CAUTION

A ground-fault circuit-interrupter must be provided if this device is used to control underwater lighting fixtures. The 

conductors on the load side of the ground-fault circuit-interrupter shall not occupy conduit, boxes, or enclosures 

containing other conductors unless the additional conductors are also protected by a ground-fault circuit-interrupter. 

Refer to local codes for complete details.

SAVE THESE INSTRUCTIONS

  WARNING

People with infectious diseases should not use a spa or hot tub.

To avoid injury, exercise care when entering or exiting the spa or hot tub.

Do not use drugs or alcohol before or during the use of a spa or hot tub to avoid unconsciousness and possible 

drowning.

Pregnant or possibly pregnant women should consult a physician before using a spa or hot tub. 

Water temperature in excess of 100°F (38°C) may be injurious to your health. 

Before entering a spa or hot tub, measure the water temperature with an accurate thermometer. 

Do not use a spa or hot tub immediately following strenuous exercise.

Prolonged immersion in a spa or hot tub may be injurious to your health.

Do not permit any electric appliance (such as a light, telephone, radio, or television) within 5 feet (1,52m) of a spa 

or hot tub.

The use of alcohol, drugs or medication can greatly increase the risk of fatal hyperthermia in hot tubs and spas.

Water temperature in excess of 100°F (38°C) may be hazardous to your health. 

Attention installer:  

Install to provide drainage of compartment for electrical components.

Page 5

ENGLISH

  

 

iAquaLink™ Web Connect Device AquaLink

®

 RS and PDA Control Systems   

|

   Installation Manual

Summary of Contents for iAquaLink

















Reviews: