background image

4

 General Cleaner 

Operation

 CAUTION

To prevent damage to the cleaner, be sure to adhere 

to the following guidelines:

•  Remove the cleaner from the pool after the 

cleaning cycle is completed.

•  Store on the caddy and out of direct sunlight or 

inclement weather.

•  Never lift the cleaner out of the pool by the 

fl oating cable. Always use the lift feature to 

remove cleaner from the pool. 

•  Take additional care when lifting the cleaner out 

of the pool. It becomes heavier when fi lled with 

water.

•  Always remove the cleaner from pool when super 

chlorinating or adding acid.

•  Do not handle cleaner while it is in operation

IMPORTANT

•  Always make sure the cleaner head is fully 

submerged before you begin operation.

•  Clean the fi lter canister after each cleaning 

cycle.

•  Do not leave your cleaner in the pool on a 

permanent basis.

•  At the end of each cycle, remove the cleaner 

from the pool. 

•  Start at the cleaner head and untangle any 

coils in the cable before storing the cleaner.

The robotic cleaner includes a safety feature that 

automatically stops the cleaner if it is powered 

on but not submerged in water. For pools 

equipped with a beach area, this safety feature is 

programmed to drive the cleaner in reverse and 

back into the pool when the impeller is out of the 

water. 

We recommend not exceeding 3 cleaning cycles 

per week.

Install and Submerge the Cleaner

1.  With the Control Unit plugged into a power 

outlet, spread the fl oating cable across the 

pool deck until you reach the middle of the 

pool length.

2.  At the center point, submerge the cleaner 

in the pool and hold in the vertical position 

to release any air trapped inside. (Figure 

11).

1

Figure 11.  Submerge the Cleaner Vertically

3.  Ensure the unit sinks to the bottom of the 

pool and does not fl oat 

(Figure 12).

2

Figure 12.  Cleaner Sinking to the Bottom of the 

Pool

Page

 9 

  

Zodiac

®

 Duo-X

  Robotic Pool Cleaners   

|

   Owner's Manual

Summary of Contents for Duo-X DX4000

























Reviews: