manualshive.com logo in svg

Zimmer Soleoline, Service, Page: 25 / 34

Share
Download
Zimmer Soleoline Service Download Page 25

 

 

Soleo

line

 Service  

 

Rev. B 

26.07.10 

 

-25- 

K:\GRUPPE\QS\MDD-Doku\Service Handbuch soleoline.doc 

 

10.3.  Starting Problems 

 

10.3.1.  The device does not run, the display is dark and there is no acoustic signal. 

 

Plug in the power cable. 

 

Turn on the power switch. 

 

Check the mains fuses. To do this, unplug the mains cable.  

 

The mains fuses are located behind the coverage on the power inlet. Loosen the upper and 
lower fastenings of the fuse holder with a screwdriver and remove the fuse holder. Inspect the 
fuses and replace with fuses of the same type and rating, if necessary. 

 

If the above measures are not successful, please contact customer service. 

 

10.3.2.  The device is running, the acoustic signal after switching on the device was there but the 

display does not run 

 

Check the display serial cable. Therefore open the cover and check, if the display cable is 
correctly attached. 

 

After reattached the cable, close the cover and connect the power inlet cable and start the 
device. 

 

If the above measures are not successful, please contact customer service. 

 

10.3.3.  The device is running, the acoustic signal after switching on the device was there, the start 

window is displayed but there is no reaction to the touch of the screen 

 

Check the touch cable. Therefore open the cover and check, if the touch cable is correctly 
attached. 

 

After reattached the cable, close the cover and connect the power inlet cable and start the 
device. 

 

If the above measures are not successful, please contact customer service. 

 

 

10.3.4.  The device is running, the acoustic signal after switching on the device was there but the 

display is dark and there is not reaction to touch of the screen 

 

Check the backlight cable. Therefore open the cover and check, if the backlight cable ist 
correctly attached. 

 

After reattached the cable, close the cover and connect the power inlet cable and start the 
device. 

 

If the above measures are not successful, please contact customer service. 

 

10.3.5.  There is no acoustic signal even if an error message is displayed. 

 

Unplug the power cable from the power inlet.  

 

Opening the cover.  

 

Check if the speaker cable is attached to the main board. 

 

Reattach the cable and close the cover. 

 

If the above measures are not successful, please contact customer service. 

 
 
 
 
 

Summary of Contents for Soleoline



































Reviews:

No comments