manualshive.com logo in svg

Zimmer Soleoline, Service, Page: 23 / 34

Share
Download
Zimmer Soleoline Service Download Page 23

 

 

Soleo

line

 Service  

 

Rev. B 

26.07.10 

 

-23- 

K:\GRUPPE\QS\MDD-Doku\Service Handbuch soleoline.doc 

 

9.  Technical Data 

Operating voltage 
Soleo

line

 

100-240 V, 220 V / 50/ 60 Hz

 

 

Operating voltage Vaco

 

100-120V/ 50Hz/ 60Hz or  
230-240V/ 50Hz/ 60Hz 

 

Power consumption 
soleo

line

 

max. 60 VA 

 

Power consumption Vaco 

max. 50 VA 

 

Fuse Soleo

line

 

2x 2AT 

 

Fuse Vaco 

2x 0,25AT (100-120V device) 
2x 0,4AT (230-240V device) 

 

Protection class Soleo

line

 

IEC 601-1, Class 2, Type BF 

 

 

Protection class Vaco

 

IEC 601-1, Class 2, Type BF 

 

 

MDD/MPG (SonoStim) 
MDD/MPG (Galva) 

 

Class IIb 
Class IIa

 

 

MDD/MPG (Vaco) 
 

 

 

 

Class IIa

 

 

Housing dimensions

 

 

 

Soleoline  

322mm x 234mm x 130mm 

 

Soleoline with Vaco 

322mm x 234mm x 260mm 

 

 

 

 

Weight 

 

 

Soleoline 

2,1kg 

 

Sonoline with Vaco 

5,1kg 

 

 

 

 

Transport 

The device should only be shipped in its original packaging

 

 

 

 

 

Ambient temperature in 
operation: 

 

+10 °C – +40 °C, 30% - 75% rel. humidity,  
700 kPa – 1060 kPa 

 

 

 

 

Storage 

-10 °C – +50 °C, 10% - 90% rel. humidity,  
700 kPa – 1060 kPa 

 

 
 

 

Summary of Contents for Soleoline



































Reviews:

No comments