Zetor Forterra HD 130 Operator'S Manual Download | Manualshive

Page: 139 / 168

background image

Reassembly of the air cleaner elements

Hydrostatic steering oil tank

Replacing the filtration element of the hydrostatic steering

When reassembling the air cleaner elements proceed in
the reverse order.
Observe the following points during the element
reassembly:
- Make sure the contact surfaces are clean.

- During the assembly the elements must not get
deformed and after installation they must not vibrate.
- After closing of the cleaner with the lid the whole cleaner
must be perfectly leak-proof.
- After the maintenance of the dry air cleaner ensure
proper functioning of the clogging indicator again.

G715

The tank is accessible after opening the hood. It is found
in the front part on the left side of the tractor.
By dipstick check (A) the height of oil level in hydrostatic
steering tank, keep the level of oil between MIN. and
MAX. marks, see fig. (A).
If necessary, replenish the oil after nut disassembly (1)
and removing the lid of tank.

W3

1 - Dismantle the left rear side plate of the hood
2 - Place a suitable container under the hydrostatic
steering tank
3 - Release the drain screw
4 - Drain oil from the tank

F_02_107

5 - Unscrew the tank lid
6 - Replace the filtration element
7 - Install the new element

XF_02_141

MAINTENANCE INSTRUCTIONS

138

138

«
...
137
138
139
140
141
...
»

Summary of Contents for Forterra HD 130









































































































































































Reviews:

No comments

Related manuals for Forterra HD 130

Brand: Ditch Witch Pages: 103

Farmall 105U Efficient Power

Brand: Case IH Pages: 61

Brand: New Holland Pages: 41

Brand: Komatsu Pages: 6

Brand: Komatsu Pages: 6

Brand: Komatsu Pages: 6

Brand: Amica Pages: 60

Brand: Amica Pages: 68

Brand: New Holland Pages: 41

Workmaster 25S Tier 4B

Brand: New Holland Pages: 41

Brand: New Holland Pages: 61

Brand: Farmall Pages: 132

Brand: WALTERSCHEID Pages: 20

Brand: Land Pride Pages: 36

Proxima GP Series

Brand: Zetor Pages: 226

YTA18542 / 96045005500 NO. 960 45 00-55

Brand: Husqvarna Pages: 64

Brand: Husqvarna Pages: 88

Brand: Bush Hog Pages: 54

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands