Zetor Forterra HD 130 Operator'S Manual Download | Manualshive

Page: 147 / 168

background image

Maintenance and treatment of tyres

F_02_122a

Regularly check the outer surface of tyres and verify whether they are free of defects at the sides and over
the bead and whether the reinforcement is not damaged.

Do not use tyres that show a defect any longer.

Tyre inflation

The basic recommended inflation values are specified in the table. Regularly check the tyre pressure before
driving, when the tyres are cold. To inflate the tyres use the pressure controller (B), which acts as a pressure
equalizer, tyre filling device and safety valve. Remove the rubber cap of the pressure controller and screw
a tyre inflation hose instead. Screw the hose up to the end of the thread to compress the non-return valve. If
there is the maximum pressure in the air reservoir (A), the tyres cannot be inflated. In this case you must first
reduce the pressure with the condensate drain valve located in the bottom part of the air reservoir (A). After

inflating the tyres you must put the rubber cap back on the pressure controller.

Recommended inflation values of the front wheel tyres

The value of the permitted load-bearing capacity of the front axle must not exceed the sum of the load-
bearing capacity values of both the tyres that are installed on the axle. The values of the permitted load-
bearing capacity of the axles are specified in the 'Main technical parameters' of the corresponding tractor

type. On the same axle of the tractor there must not be tyres of different dimensions and designs (in this
case tyre design means the diagonal or radial tyre version).

Tyredimensions and design

Principal working
activity

480/70 R24

420/70R28

480/65 R24

For field work

Inflation (kPa)

130-160

130-160

130-160

Load-bearing capacity
(kg)

2035-2360

1860-2060

2000-2240

For road transport

Inflation (kPa)

160-190

160-190

160-190

Load-bearing capacity
(kg)

2035-2360

1860-2060

2000-2240

For work with a front
loader at the maximum
permitted speed of
8 km/h.

Inflation (kPa)

200

200

200

Load-bearing capacity
(kg)

max. 2830

max. 2040

max. 1910

MAINTENANCE INSTRUCTIONS

146

146

«
...
145
146
147
148
149
...
»

Summary of Contents for Forterra HD 130









































































































































































Reviews:

No comments

Related manuals for Forterra HD 130

Brand: K&M Pages: 9

Brand: Ariens Pages: 44

Brand: Holder Pages: 16

Brand: Vari Pages: 44

Brand: New Holland Pages: 41

Brand: Ventrac Pages: 37

Brand: Cub Cadet Pages: 61

Brand: Jacobsen Pages: 86

Brand: Walker Pages: 28

Brand: Hardi Pages: 170

Brand: SAME Pages: 41

Brand: MTD Pages: 33

Brand: AVANT Pages: 18

Brand: AVANT Pages: 18

Brand: AVANT Pages: 18

Brand: AVANT Pages: 18

Brand: AVANT Pages: 20

Brand: AVANT Pages: 22

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands