Zetor Forterra HD 130 Operator'S Manual Download

Page: 101 / 168

Limitation of the upper position of the three-point hitch

Lowering speed

Free position

Setting the control of three-point hitch

It is activated with the control (5). The limitation can be

implemented in the upper half of the three-point hitch lift.

F_02_169

The lowering speed of the three-point hitch is set with the

control (3).

In the vibration dampening mode and during

the use of the rear control buttons the lowering speed

setting is out of function.

Symbol of the maximum

lowering speed

Symbol of the minimum

lowering speed

F_02_170

For permanent work with free hydraulic system, e.g.

during work with a plough with a support wheel the

position of the control (4) under the indication (A) and the

position of the control (6) at the positional control symbol

is used.

F_02_171

Electrohydraulics enables two ways of three-point hitch

control.

A. Manual control setting - control (6) is set in the range

see arrow

B. Automatic control - control (6) is set in HitchTronic

(AHC) position see arrow

Automatic control can be at any time exchanged for

manual and the other way round by a control (6).

ahc_01

ELECTRO-HYDRAULIC SYSTEM

100

Summary of Contents for Forterra HD 130









































































































































































Search results

Summary of Contents for Forterra HD 130

Reviews:

Related manuals for Forterra HD 130

Brands by name

Popular brands

Zetor Forterra HD 130, Operator'S Manual

Search results

Summary of Contents for Forterra HD 130

Reviews:

Related manuals for Forterra HD 130

Brands by name

Popular brands