Zetor Forterra HD 130 Operator'S Manual Download Page 39 | Manualshive

Page: 39 / 168

background image

Display - resetting data

Display - manual brake

Display - error messages

Resetting data marked with an arrow can be done on
a display (4) and (5). Select display (4) or (5) with a button
(A) and by a longer pressing of button (B) reset data
marked with an arrow.

FHD14N059

If the tractor is not braked by a manual brake, a warning is
displayed on a display (letter

P

in a circle) and at the same

time a sound signal is heard. See the chapter 'Driving
operation' for more.

Brake the tractor by a manual brake.

FH12N039

Serious faults in the system (1)
STOP

sign, number of fault (1) is displayed on a display

with serious faults.

If this situation occurs, set the tractor aside and

contact service.

Less serious faults in the system (2) a (3)

With less serious faults in the system, the number of faults
(2) are displayed on the display for a time period of
approximately 5 seconds.
Then the display of fault is minimized to the main field. (3)

If this situation occurs, complete the work and

contact service.

See more in the chapter of 'Driving operation'.

FHD14N002

ACQUAINTANCE WITH THE TRACTOR

38

38

«
...
37
38
39
40
41
...
»

Summary of Contents for Forterra HD 130









































































































































































Reviews:

No comments

Related manuals for Forterra HD 130

Brand: Kverneland Pages: 74

Brand: GOLDONI Pages: 160

Brand: Farmall Pages: 132

Brand: Zenoah Pages: 96

Brand: GE Pages: 24

Brand: Murray Pages: 32

Brand: Murray Pages: 52

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands