background image

PREMIER AD INSTALLATION MANUAL.  

 

 

Software Version  :PANEL-R1578 & LOOP-R1062 

 

Approved Document No: GLT.MAN-105A

 

 

 

 

PAGE 8

 

Issue : 2.02         Authorised: GH      Date: 16/07/2007 

6 CONNECTING MAINS & BATTERY POWER 

 

6.1 CONNECTING THE MAINS POWER 

 

INLET MAINS
 SUPPLY

 

 

Figure 3: Power Supply PCB layout and Mains connection details

 

 

 

6.2 CONNECTING THE BATTERIES 

 

 

LINK WIRE

  

 
 

 

Figure 4:  Battery location and connection details

 

The panel should be connected to 220-240V AC by a 3A 
rated spur to the fuse box with 1mm

to 2.5mm

3-core 

cable. Nothing else should be connected to this supply. 
The cable should be fire resistant 

 

The Live, Earth and Neutral connections are marked on the 
PCB. The Mains is protected by a quick blow 20mm 2A 
HBC fuse. (Also known as HRC) 

 

The incoming mains cable should be kept separate from 
the zone cables to help minimise mains interference.  

 

Once the mains is connected, the protective cover should 
be replaced BEFORE turning on the mains power. This will 
minimise the chance of electric shock from the PCB.

  

 

MAKE SURE ANY SPARE ENTRY HOLES ARE 
COVERED WITH THE PLASTIC GROMMETS PROVIDED

 

 

It is advisable to apply power to the panel before 
connecting any devices, to check for correct 
operation, and to familiarise yourself with the fire 
alarm panels controls. 
 

Although there are many sizes of suitable 
battery, the sizes we usually recommend for 
the Premier AD are 12V 7Ah, or 12V 12AH  
 
To calculate the exact requirement, use the 
equation in section 16, BATTERY 
CONNECTIONS 

 

The two batteries are wired in 

series

.  

 

The 

+ve

 of one battery is connected to the 

red

 

battery lead. 

 

The 

–ve

 of the other battery is connected to 

the 

black

 battery lead. 

 

The –ve of the first battery is connected to the 
+ve of the second battery using the link wire 
supplied. 

 

When fitting the batteries, take care not to 
damage the temperature monitoring 
thermistor. 

This is used to prevent 

overcharging the batteries in high ambient 
temperatures.

 

Summary of Contents for NPAD 2


































Reviews: