background image

 

NOTICE TO PURCHASERS AND USERS OF OUR 

PRODUCTS AND THIS INFORMATIONAL MATERIAL

 

 

Clemco proudly provides products for the abrasive blast industry 
and is confident that industry professionals will use their knowledge 
and expertise for the safe and efficient use of these products.

 

 

The products described in this material, and the information 
relating to these products, are intended for knowledgeable, 
experienced users. It is the responsibility of the user to insure that 
proper training of operators has been performed and a safe work 
environment is provided.

 

 

No representation is intended or made as to: the suitability of the 
products described here for any purpose or application, or to the 
efficiency, production rate, or useful life of these products. All 
estimates regarding production rates or finishes are the 
responsibility of the user and must be derived solely from the user’s 
experience and expertise, not from information contained in this 
material.

 

 

It is possible that the products described in this material may be 
combined with other products by the user for purposes determined 
solely by the user. No representations are intended or made as to 
the suitability of or engineering balance of or compliance with 
regulations or standard practice of any such combination of products 
or components the user may employ.

 

 

This equipment is only one component of a cabinet blasting 
operation. Other products, such as air compressors, air filters and 
receivers, abrasives, equipment for ventilating, dehumidifying, or 
other equipment, even if offered by Clemco, may have been 
manufactured or supplied by others. The information Clemco 
provides is intended to support the products Clemco manufactures. 
Users must contact each manufacturer and supplier of products 
used in the blast operation for warnings, information, training, and 
instruction relating to the proper and safe use of their equipment.

 

BNP-160 TUMBLE BASKET

SUCTION BLAST CABINET

O. M. 25993

DATE OF ISSUE:  03/13 
REVISION: 

Rev. B, 05/18 

 

 

© 2018 CLEMCO INDUSTRIES CORP. 

One Cable Car Dr. 

Washington, MO 63090 

Phone (636) 239-4300 

Fax

 

(800)

 

726-7559 

Email: [email protected] 

www.clemcoindustries.com 

Summary of Contents for BNP-160
























Reviews: